Konica Minolta magicolor 3730DN magicolor 3730DN User Guide - Page 98

Replacing the Fuser Unit FU-P02, FUSER, LIFE END

Get Konica Minolta magicolor 3730DN PDF manuals and user guides View all Konica Minolta magicolor 3730DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Replacing the Fuser Unit FU-P02 When the time to replace the fuser unit is reached, the message FUSER LIFE END appears. Printing can continue even after this message appears; however, since the print quality is reduced, the fuser unit should be replaced immediately 1 Turn off the printer. Note There are extremely hot parts within the machine. Before replacing the fuser unit, wait about 20 minutes after turning off the machine, and then check that the fusing section has reached room temperature, otherwise, you may get burnt. 2 Open the right side cover. 3 Open the eject cover. Replacing Consumables 5-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Replacing Consumables
5-27
Replacing the Fuser Unit FU-P02
When the time to replace the fuser unit is reached, the message
FUSER
LIFE END
appears. Printing can continue even after this message
appears; however, since the print quality is reduced, the fuser unit should be
replaced immediately
1
Turn off the printer.
Note
There are extremely hot parts within the machine. Before replacing the
fuser unit, wait about 20 minutes after turning off the machine, and then
check that the fusing section has reached room temperature, otherwise,
you may get burnt.
2
Open the right side cover.
3
Open the eject cover.