Lenovo H430 Lenovo H4 Series Hardware Maintenance Manual V2.0 - Page 21

Using Device

Get Lenovo H430 PDF manuals and user guides View all Lenovo H430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Chapter 5. Using the Setup Utility press Enter. 3. The password dialog box will be displayed. Type the new password, and press Enter. 4. when prompted to confirm the password, type the password again. If you type the password correctly, the password will be installed. To delete a previously set user password, do the following : Note: When prompted for a password, you must type your supervisor password. 1. From the Setup Utility program menu, select Change User Password and press Enter. 2. when you type the user password. a message will display that Enter New Password. Press Enter and a message will display that indicates the password has been disabled. 3. Press any key to contine. Using Device Device is used to enable or disable user access to the following device: PS/2 Mouse Support When this feature is set to Disable, the device of PS/2 Mouse Support is disabled and will not be displayed in the system configuration. To set Device, do the following: 1. Start the Setup Utility program (see "Starting the Setup Utility program" on page 16). 2. From the Setup Utility program menu, select Device. 3. Select Onboard PS/2 Mouse Support. 4. Select Disable or Enable and press Enter. 5. Return to the Setup Utility program menu and select Exit and then Save changes and Exit. Note: If you do not want to save the settings, select Discard Changes and Exit or Discard Changes. You can set others such as Floppy Drive Setup, Serial Port Setup, Parallet Port Setup, USB Setup, Video Setup, Audio Setup, Network Setup and so on. See the information displayed on the right side of the screen. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Chapter 5. Using the Setup Utility
19
press Enter.
3. The password dialog box will be displayed. Type the new password, and
press Enter.
4. when prompted to confirm the password, type the password again. If
you type the password correctly, the password will be installed.
To delete a previously set user password, do the following :
Note:
When prompted for a password, you must type your supervisor
password.
1. From the Setup Utility program menu, select
Change User Password
and press
Enter
.
2. when you type the user password. a message will display that
Enter
New Password
. Press Enter and a message will display that indicates the
password has been disabled.
3. Press any key to contine.
Using Device
Device is used to enable or disable user access to the following device:
PS/2 Mouse Support
When this feature is set to
Disable
, the device
of PS/2 Mouse Support is disabled and will
not be displayed in the system configuration.
To set Device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program”
on page 16).
2. From the Setup Utility program menu, select
Device
.
3. Select
Onboard PS/2 Mouse Support
.
4. Select
Disable
or
Enable
and press Enter.
5. Return to the Setup Utility program menu and select
Exit
and then
Save
changes and Exit
.
Note:
If you do not want to save the settings, select
Discard Changes
and Exit
or
Discard Changes
. You can set others such as
Floppy
Drive Setup, Serial Port Setup, Parallet Port Setup, USB Setup,
Video Setup, Audio Setup, Network Setup
and so on. See the
information displayed on the right side of the screen.