Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre Edge 62 » Manual Viewer

Lenovo ThinkCentre Edge 62 Hardware Maintenance Manual - Page 82

Voltage Sensors Test Passed, Voltage Sensors failure

View all Lenovo ThinkCentre Edge 62 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Diagnostic Error Code 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold exceeded 089-197-XXX Microprocessor test warning 089-198-XXX Microprocessor test aborted 089-199-XXX Microprocessor test failed, cause unknown 170-000-XXX Voltage Sensor(s) Test Passed 170-0XX-XXX Voltage Sensor(s) failure 170-195-XXX Voltage Sensor(s) Test aborted by user 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 170-197-XXX Voltage Sensor(s) test warning 170-198-XXX Voltage Sensor(s) test aborted FRU/Action 1. See "Undetermined problems" on page 82. 2. Flash the system and re-test. See "Flash update procedures" on page 167. 3. Replace component under function test. No action 1. Microprocessor(s) 2. System board Information only Restart the test, if necessary. 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 57. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 1. Flash the system. See "Flash update procedures" on page 167. 2. Go to "Undetermined problems" on page 82. 1. See "Undetermined problems" on page 82. 2. Flash the system and re-test. See "Flash update procedures" on page 167. 3. Replace component under function test. No action 1. Flash system 2. System board Information only Restart the test, if necessary. 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 57. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 57. 2. Flash the system and re-test. See "Flash update procedures" on page 167. 3. Go to "Undetermined problems" on page 82. 76 ThinkCentre Edge Hardware Maintenance Manual

Section	Page
Chapter 1. About this manual	7
Important Safety Information	7
Chapter 2. Safety information	9
General safety	9
Electrical safety	9
Safety inspection guide	11
Handling electrostatic discharge-sensitive devices	11
Grounding requirements	12
Safety notices (multi-lingual translations)	12
Chapter 3. General information	35
Lenovo ThinkVantage Tools	35
Lenovo Welcome	35
Lenovo ThinkVantage Toolbox	35
Lenovo Solution Center	35
SimpleTap	36
Additional information resources	36
Specifications	37
Chapter 4. General Checkout	39
Problem determination tips	39
Chapter 5. Troubleshooting and diagnostics	41
Basic troubleshooting	41
Troubleshooting procedure	42
Troubleshooting	43
Audio problems	43
CD problems	44
DVD problems	45
Intermittent problems	47
Keyboard, mouse, or pointing device problems	47
Monitor problems	49
Networking problems	50
Option problems	53
Performance and lockup problems	54
Printer problems	55
Serial port problems	55
Software problems	56
USB problems	57
Diagnostics	57
Lenovo ThinkVantage Toolbox	57
Lenovo Solution Center	58
PC-Doctor for DOS	58
Chapter 6. Using the Setup Utility program	63
Starting the Setup Utility program	63
Viewing and changing settings	63
Using passwords	63
Password considerations	63
Power-On Password	64
Administrator Password	64
Setting, changing, and deleting a password	64
Enabling or disabling a device	64
Selecting a startup device	65
Selecting a temporary startup device	65
Selecting or changing the startup device sequence	65
Exiting the Setup Utility program	65
Chapter 7. Symptom-to-FRU Index	67
Hard disk drive boot error	67
Power Supply Problems	67
Diagnostic error codes	68
Beep symptoms	85
POST error codes	85
Miscellaneous error conditions	86
Undetermined problems	88
Chapter 8. Replacing FRUs	89
Locating connectors, controls, and indicators on the front of your computer	90
Locating connectors on the rear of your computer	91
FRU locations	92
System board parts and connectors	94
Removing and reinstalling the system stand hinge cover	95
Removing and reinstalling the system stand	96
Removing and reinstalling the foot stands	98
Removing the computer cover	101
Replacing the hard disk drive	102
Replacing the optical drive	104
Removing the VESA mount bracket	105
Replacing the rear I/O assembly	106
Removing and reinstalling the system board shield	108
Replacing the power supply	109
Replacing the microprocessor fan	110
Replacing the heat sink assembly	111
Replacing the microprocessor	113
Replacing the card reader	116
Opening the system board shield window	117
Replacing the battery	118
Replacing the inverter	119
Installing or replacing a memory module	120
Replacing the internal speakers	122
Replacing the integrated camera	123
Replacing the system board	124
Replacing the LCD panel	126
Replacing the WI-FI card	130
Completing the parts replacement	131
Chapter 9. FRU lists	133
Overall: MT 5068, 7558, and 7567	133
Mechanical FRUs	140
Keyboard and Mouse	141
Adapters and miscellaneous FRUs	156
Power Cords	156
Recovery discs	161
Windows 7 Starter 32 SP1 Recovery CD	161
Windows 7 Home Basic 32 SP1 Recovery CD	162
Windows 7 Home Premium 32 SP1 Recovery CD	163
Windows 7 Home Premium 64 SP1 Recovery CD	164
Windows 7 Professional 32 SP1 Recovery CD	166
Windows 7 Professional 64 SP1 Recovery CD	168
Windows 7 Home Basic 64 SP1 Recovery CD	170
Windows XP Professional Generic Recovery CD	170
Chapter 10. Additional Service Information	173
Security features	173
Hardware controlled Passwords	173
Operating system password	173
Vital product data	173
BIOS levels	173
Flash update procedures	173
Updating (flashing) the BIOS from a disc	173
Updating (flashing) the BIOS from your operating system	174
Recovering from a POST/BIOS update failure	174
Power management	175
Automatic configuration and power interface (ACPI) BIOS	175
Automatic Power-On features	175
Appendix A. Notices	177
Television output notice	178
European conformance CE mark	178
Trademarks	178

Match case Limit results 1 per page

Diagnostic Error Code

FRU/Action

086-199-XXX

Mouse Port interface test failed, cause

unknown

1. See “Undetermined problems” on page 82.

2. Flash the system and re-test. See “Flash update

procedures” on page 167.

3. Replace component under function test.

089-000-XXX

Microprocessor Test Passed

No action

089-XXX-XXX

Microprocessor failure

1. Microprocessor(s)

2. System board

089-195-XXX

Microprocessor Test aborted by user

Information only Restart the test, if necessary.

089-196-XXX

Microprocessor test halt, error threshold

exceeded

1. Press F3 to review the log ﬁle.

2. Restart the test to reset the log ﬁle.

089-197-XXX

Microprocessor test warning

1. Make sure the component that is called out is

connected and/or enabled. See Chapter 6 “Using

the Setup Utility program” on page 57.

2. Re-run test.

3. Replace the component that is called out in warning

statement.

4. Replace the component under test.

089-198-XXX

Microprocessor test aborted

1. Flash the system. See “Flash update procedures”

on page 167.

2. Go to “Undetermined problems” on page 82.

089-199-XXX

Microprocessor test failed, cause unknown

1. See “Undetermined problems” on page 82.

2. Flash the system and re-test. See “Flash update

procedures” on page 167.

3. Replace component under function test.

170-000-XXX

Voltage Sensor(s) Test Passed

No action

170-0XX-XXX

Voltage Sensor(s) failure

1. Flash system

2. System board

170-195-XXX

Voltage Sensor(s) Test aborted by user

Information only Restart the test, if necessary.

170-196-XXX

Voltage Sensor(s) test halt, error threshold

exceeded

1. Press F3 to review the log ﬁle.

2. Restart the test to reset the log ﬁle.

170-197-XXX

Voltage Sensor(s) test warning

1. Make sure the component that is called out is

connected and/or enabled. See Chapter 6 “Using

the Setup Utility program” on page 57.

2. Re-run test.

3. Replace the component that is called out in warning

statement.

4. Replace the component under test.

170-198-XXX

Voltage Sensor(s) test aborted

1. If a component is called out, make sure it is

connected and/or enabled. See Chapter 6 “Using

the Setup Utility program” on page 57.

2. Flash the system and re-test. See “Flash update

procedures” on page 167.

3. Go to “Undetermined problems” on page 82.

ThinkCentre Edge Hardware Maintenance Manual