Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre M58e » Manual Viewer

Lenovo ThinkCentre M58e Hardware Maintenance Manual - Page 101

Replacing the Internal speaker, Completing the FRU replacement, into the metal speaker slots

View all Lenovo ThinkCentre M58e manuals

Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Replacing the Internal speaker Attention Do not open your computer or attempt any repair before reading and understanding the "Important safety information" in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the internal speaker. 1. Remove the computer cover. See "Removing the computer cover" on page 69. 2. Remove the front bezel. See "Removing and installing the front bezel" on page 70 3. Locate the internal speaker connector on the system board. See "System board connectors" on page 68. 4. Disconnect the internal speaker cable from the system board. 5. Use a blunt instrument (such as, the top of a ball point pen) to disengage one of the internal-speaker-locking tabs 2 and slide that side of the speaker 1 upward enough to keep the locking tab disengaged. Then disengage the other internal-speaker-locking tab and slide the internal speaker upward until the speaker is released. 6. Route the speaker cable and then position the new internal-speaker tabs 3 into the metal speaker slots and then push the internal speaker downward until the speaker-locking tabs snap into position. 7. Connect the speaker cable to the system board. See "System board connectors" on page 68. 8. Go to "Completing the FRU replacement" on page 95. Completing the FRU replacement After replacing FRUs, you need to install any removed parts, replace the cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the FRU that is replaced, you might need to confirm the updated information in the Setup Utility program. Note: When the power cord is first plugged in, the computer might appear to turn on for a few seconds and then turn off. This is a normal sequence to enable the computer to initialize. Chapter 8. Replacing FRUs (Types 7258, 7260, 7268, 7270, 7280, 7296, 7298, 7304, 7307,7413, 7491, and 7508) 95

Section	Page
Chapter 1. About this manual	7
Important Safety Information	7
Important information about replacing RoHS compliant FRUs	7
Turkish statement of compliance	8
Chapter 2. Safety information	9
General safety	9
Electrical safety	9
Voltage-selection switch	11
Safety inspection guide	11
Handling electrostatic discharge-sensitive devices	12
Grounding requirements	12
Safety notices (multi-lingual translations)	12
Chapter 3. General information	35
The ThinkVantage Productivity Center program	35
Additional information resources	35
Specifications	35
Types 7258, 7260, 7268, 7270, 7280, 7296, 7298, 7304, 7307,7413, 7491, and 7508	36
Types 7259, 7267, 7269, 7279, 7297, 7303, 7306, 7487, 7506, and 7514	36
Chapter 4. General Checkout	39
Problem determination tips	39
Chapter 5. Diagnostics	41
Lenovo System Toolbox	41
PC-Doctor for Windows PE	41
Running diagnostics from the Rescue and Recovery workspace	41
PC-Doctor for DOS	42
Creating a diagnostic CD/DVD image	42
Running diagnostics from the disc	42
Navigating through the diagnostics programs	42
Running tests	42
Viewing the test log	44
Chapter 6. Using the Setup Utility	45
Starting the Setup Utility program	45
Viewing and changing settings	45
Using passwords	45
Password considerations	45
Power-On Password	46
Privileged Access Password	46
Setting, changing, and deleting a password	46
Enabling or disabling a device	46
Selecting a startup device	47
Selecting a temporary startup device	47
Selecting or changing the startup device sequence	47
Advanced settings	47
Exiting from the Setup Utility program	47
Chapter 7. Symptom-to-FRU Index	49
Hard disk drive boot error	49
Power Supply Problems	49
Diagnostic error codes	50
Beep symptoms	67
POST error codes	68
Miscellaneous error messages	69
Undetermined problems	71
Chapter 8. Replacing FRUs (Types 7258, 7260, 7268, 7270, 7280, 7296, 7298, 7304, 7307,7413, 7491, and 7508)	73
Locations	73
Rear connectors	73
Computer components	74
System board connectors	74
Removing the computer cover	75
Removing and installing the front bezel	76
Replacing the power supply assembly	77
Replacing the system board	78
Replacing the heat sink and fan assembly	80
Replacing the microprocessor	81
Replacing a memory module	85
Installing or replacing an adapter card	86
Replacing the primary hard disk drive	88
Replacing the secondary hard disk drive	91
Replacing an optical drive	94
Replacing the diskette drive or card reader	94
Replacing the front fan assembly	96
Replacing the rear fan assembly	97
Replacing the front audio/USB assembly	99
Replacing the power switch/LED assembly	99
Replacing the CMOS battery	100
Replacing the Internal speaker	101
Completing the FRU replacement	101
Chapter 9. Replacing FRUs (Types 7259, 7267, 7269, 7279, 7290, 7297, 7303, 7306, 7408, 7487, 7506 and 7514)	103
Locations	103
Rear connectors	103
Computer components	104
System board connectors	104
Opening the cover	105
Accessing system board components and drives	106
Replacing a memory module	106
Replacing the battery	107
Replacing the power supply	108
Replacing the system board	110
Replacing the microprocessor	113
Replacing the heat sink and fan assembly	115
Replacing the hard disk drive	116
Replacing the optical drive	118
Replacing the internal speaker	120
Replacing the power switch/LED assembly	121
Replacing the card reader	122
Installing or replacing an adapter card	122
Completing the FRU replacement	124
Chapter 10. FRU lists	127
Overall: MT 7258, 7260, 7268, 7270, 7280, 7296, 7298, 7304, 7307,7413, 7491, and 7508	127
Mechanical FRUs	153
Keyboard and Mouse	164
Adapters and miscellaneous FRUs	207
Power Cords	215
Recovery discs	227
Overall: MT 7259, 7267, 7269, 7279, 7297, 7303, 7306, 7487, 7506, and 7514	323
Mechanical FRUs	353
Keyboard and Mouse	365
Adapters and miscellaneous FRUs	407
Power Cords	416
Recovery discs	428
Chapter 11. Additional Service Information	527
Security features	527
Hardware controlled Passwords	527
Operating system password	527
Vital product data	527
BIOS levels	527
Flash update procedures	527
Updating (flashing) BIOS from a disc	528
Updating (flashing) BIOS from your operating system	528
Recovering from a POST/BIOS update failure	528
Power management	529
Automatic configuration and power interface (ACPI) BIOS	529
Automatic Power-On features	529
Appendix A. Notices	531
Television output notice	532
Trademarks	532

Match case Limit results 1 per page

Replacing the Internal speaker

Attention

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”

in the

ThinkCentre Safety and Warranty Guide

that came with your computer. To obtain a copy of the

ThinkCentre

Safety and Warranty Guide

, go to:

http://www.lenovo.com/support

This section provides instructions on how to replace the internal speaker.

1. Remove the computer cover. See “Removing the computer cover” on page 69.

2. Remove the front bezel. See “Removing and installing the front bezel” on page 70

3. Locate the internal speaker connector on the system board. See “System board connectors” on page 68.

4. Disconnect the internal speaker cable from the system board.

5. Use a blunt instrument (such as, the top of a ball point pen) to disengage one of the

internal-speaker-locking tabs

and slide that side of the speaker

upward enough to keep the

locking tab disengaged. Then disengage the other internal-speaker-locking tab and slide the internal

speaker upward until the speaker is released.

6. Route the speaker cable and then position the new internal-speaker tabs

into the metal speaker slots

and then push the internal speaker downward until the speaker-locking tabs snap into position.

7. Connect the speaker cable to the system board. See “System board connectors” on page 68.

8. Go to “Completing the FRU replacement” on page 95.

Completing the FRU replacement

After replacing FRUs, you need to install any removed parts, replace the cover, and reconnect any cables,

including telephone lines and power cords. Also, depending on the FRU that is replaced, you might need to

conﬁrm the updated information in the Setup Utility program.

Note:

When the power cord is ﬁrst plugged in, the computer might appear to turn on for a few seconds and

then turn off. This is a normal sequence to enable the computer to initialize.

Chapter 8

Replacing FRUs (Types 7258, 7260, 7268, 7270, 7280, 7296, 7298, 7304, 7307,7413, 7491, and 7508)