Lexmark T430 User's Guide - Page 151

Problem, Solution, too many sheets accumulate. You must remove the paper often

Get Lexmark T430 PDF manuals and user guides View all Lexmark T430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 151 highlights

Troubleshooting Problem Solution You are connected to the USB Make sure you are using a USB-capable operating system supported by port, but the printer did not print. your printer. Print media misfeeds or multiple feeds occur. • Make sure the print media you are using meets the specifications for your printer. See Print media sources and specifications for more information. • Flex print media before loading it in any of the sources. • Make sure the print media is loaded correctly. • Make sure the paper width and length guides on the print media sources are adjusted correctly and are not too tight. • Do not overfill the print media sources. Use the maximum stack height indicators to avoid overfilling sources. • Do not force print media into the multipurpose feeder. • Remove any curled print media from print media sources. • If the print media has a recommended print side, load the print media as described in Loading trays and Loading and using the multipurpose feeder. • Load less print media in the sources. • Turn the print media over or around and try printing again to see if feeding improves. • Do not mix print media types in the same source. • Do not mix reams of print media. • Remove the top and bottom sheets of a ream before loading the print media. • Load a print media source only when it is empty. Job prints from the wrong source Check the Paper Type setting in the printer driver or on the operator or on the wrong print media. panel. Print media does not stack neatly in an output bin. • Turn the print media stack over in the tray or multipurpose feeder. • Lift the paper rest in the standard output bin. The print media stacks more neatly. Note: Legal size paper sent to the rear exit bin stacks improperly when too many sheets accumulate. You must remove the paper often from this bin. The printer has missing or damaged parts. Contact the place where you purchased your printer. You cannot close the upper front Make sure the print cartridge is positioned correctly. door. The printer is on, but nothing prints. • Make sure the print cartridge is installed. • Make sure the parallel, USB, or Ethernet cable is firmly plugged into its corresponding connector on the back of the printer. The print media skews or buckles. • Do not overfill the standard tray or the optional 250-sheet or 500sheet tray. See print media capacity levels in Print media sources and specifications. • Make sure the guides are flush against the edges of the print media. The print media sticks together or • Remove the print media from the tray and fan it. the printer feeds multiple sheets of • Do not overfill trays. See print media capacity levels in Print media print media. sources and specifications. Solving printing problems 151

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Solving printing problems
151
Troubleshooting
You are connected to the USB
port, but the printer did not print.
Make sure you are using a USB-capable operating system supported by
your printer.
Print media misfeeds or multiple
feeds occur.
•
Make sure the print media you are using meets the specifications for
your printer. See
Print media sources and specifications
for more
information.
•
Flex print media before loading it in any of the sources.
•
Make sure the print media is loaded correctly.
•
Make sure the paper width and length guides on the print media
sources are adjusted correctly and are not too tight.
•
Do not overfill the print media sources. Use the maximum stack
height indicators to avoid overfilling sources.
•
Do not force print media into the multipurpose feeder.
•
Remove any curled print media from print media sources.
•
If the print media has a recommended print side, load the print media
as described in
Loading trays
and
Loading and using the
multipurpose feeder
.
•
Load less print media in the sources.
•
Turn the print media over or around and try printing again to see if
feeding improves.
•
Do not mix print media types in the same source.
•
Do not mix reams of print media.
•
Remove the top and bottom sheets of a ream before loading the print
media.
•
Load a print media source only when it is empty.
Job prints from the wrong source
or on the wrong print media.
Check the Paper Type setting in the printer driver or on the operator
panel.
Print media does not stack neatly
in an output bin.
•
Turn the print media stack over in the tray or multipurpose feeder.
•
Lift the paper rest in the standard output bin. The print media stacks
more neatly.
Note:
Legal size paper sent to the rear exit bin stacks improperly when
too many sheets accumulate. You must remove the paper often from
this bin.
The printer has missing or
damaged parts.
Contact the place where you purchased your printer.
You cannot close the upper front
door.
Make sure the print cartridge is positioned correctly.
The printer is on, but nothing
prints.
•
Make sure the print cartridge is installed.
•
Make sure the parallel, USB, or Ethernet cable is firmly plugged into
its corresponding connector on the back of the printer.
The print media skews or buckles.
•
Do not overfill the standard tray or the optional 250-sheet or 500-
sheet tray. See print media capacity levels in
Print media sources
and specifications
.
•
Make sure the guides are flush against the edges of the print media.
The print media sticks together or
the printer feeds multiple sheets of
print media.
•
Remove the print media from the tray and fan it.
•
Do not overfill trays. See print media capacity levels in
Print media
sources and specifications
.
Problem
Solution