Linksys RV0041 User Guide - Page 24

Port Statistics, Network Setting Status, Firewall Setting Status, on or off, Priority High or Normal

Get Linksys RV0041 - 10/100/1000 VPN Router PDF manuals and user guides
UPC - 745883562886
View all Linksys RV0041 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

10/100/1000 4-Port VPN Router Port Statistics You can check the status of any of the Router's ports simply by clicking the port number on the port diagram. If the port is disabled, it will be red; if enabled, it will be black. If it is connected, it will be green. This will open up a summary table. This summary table will show the port's settings, such as Type, Link Status (up or down), Port Disable (on or off), Priority (High or Normal), Speed Status (10Mbps,100Mbps, or 1000Mbps), Duplex Status (half or full), Auto negotiation (enable or disable). The LAN ports can be configured from the LAN Setup page of the LAN Management Tab. Network Setting Status LAN IP: This shows the Router's current LAN IP Address, and hyperlinks to that section of the Setup Tab. WAN IP: This shows the IP Address of the WAN port, hyperlinked to that section of the Setup Tab. When WAN is set up to Obtain an IP automatically, two buttons will be shown here: Release and Renew. Click the Release button to release the current IP Address and click the Renew button to update the DHCP Lease Time or get a new IP. When the WAN port is set up with PPPoE or PPTP, these two buttons will be displayed as Connect and Disconnect. Figure 5-4: Site Map Mode: This tells you if the Router's Working Mode is Gateway or Router, hyperlinked to that section of the Setup Tab DNS: All DNS Server Addresses are displayed here, with hyperlinks to that section of the Setup Tab. DDNS: This shows if the DDNS status is On or Off, with hyperlinks to that section of the Setup Tab. DNS the IP address of your ISP's server, which translates the names of websites into IP addresses DMZ Host: If this feature is enabled, the DMZ Private Address will be displayed. This is also hyperlinked to that section of the Setup Tab. Firewall Setting Status SPI (Stateful Packet Inspection): This shows if the SPI status is On or Off, hyperlinked to that section of the Firewall Tab. DoS (Denial of Service): This shows if the DoS status is On or Off, hyperlinked to that section of the Firewall Tab. Block WAN Request: This shows if the Block WAN Request status is On or Off, hyperlinked to that section of the Firewall Tab. Chapter 5: Setting Up and Configuring the Router 16 System Summary Tab

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
16
Chapter 5: Setting Up and Configuring the Router
System Summary Tab
10/100/1000 4-Port VPN Router
Port Statistics
You can check the status of any of the Router’s ports simply by clicking the port number on the port diagram. If
the port is disabled, it will be red; if enabled, it will be black. If it is connected, it will be green.
This will open up a summary table. This summary table will show the port’s settings, such as Type, Link Status
(up or down), Port Disable
(on or off), Priority (High or Normal), Speed Status (10Mbps,100Mbps, or 1000Mbps),
Duplex Status (half or full), Auto negotiation (enable or disable). The LAN ports can be configured from the LAN
Setup page of the LAN Management Tab.
Network Setting Status
LAN IP
: This shows the Router’s current LAN IP Address, and hyperlinks to that section of the Setup Tab.
WAN IP
: This shows the IP Address of the WAN port, hyperlinked to that section of the Setup Tab. When WAN is
set up to
Obtain an IP automatically
, two buttons will be shown here:
Release
and
Renew
. Click the
Release
button to release the current IP Address and click the
Renew
button to update the DHCP Lease Time or get a new
IP. When the WAN port is set up with
PPPoE
or
PPTP
, these two buttons will be displayed as
Connect
and
Disconnect
.
Mode
: This tells you if the Router’s Working Mode is
Gateway
or
Router
, hyperlinked to that section of the Setup
Tab
DNS
: All DNS Server Addresses are displayed here, with hyperlinks to that section of the Setup Tab.
DDNS
: This shows if the DDNS status is
On
or
Off
, with hyperlinks to that section of the Setup Tab.
DMZ Host
: If this feature is enabled, the DMZ Private Address will be displayed. This is also hyperlinked to that
section of the Setup Tab.
Firewall Setting Status
SPI
(Stateful Packet Inspection): This shows if the SPI status is
On
or
Off
, hyperlinked to that section of the
Firewall Tab.
DoS
(Denial of Service): This shows if the DoS status is
On
or
Off
, hyperlinked to that section of the Firewall Tab.
Block WAN Request
: This shows if the Block WAN Request status is
On
or
Off
, hyperlinked to that section of the
Firewall Tab.
Figure 5-4: Site Map
DNS
the IP address of your ISP's server, which
translates the names of websites into IP addresses