Netgear FSM7326P FSM7326P User Manual - Page 218

config acl rule match dstl4port range, config acl rule match every, every match condition.

Page 218 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software config acl rule match dstl4port range This command specifies a destination layer 4 port match condition for an ACL rule referenced by the and . The and parameters identify the first and last ports that are part of the port range. They have values from 0 to 65535. The ending port must have a value equal or greater than the starting port. The starting port, ending port, and all ports in between will be part of the destination port range. Either this command or the config acl match destl4port keyword command may be used to specify a destination layer 4 port range as a match condition. Format config acl rule match dstl4port range config acl rule match every This command specifies a match condition in which all packets match for an ACL rule referenced by the and . The parameter indicates to reinforce or negate every match condition. Format config acl rule match every config acl rule match ipdscp This command specifies the IP DiffServ Code Point (DSCP) field for an ACL rule referenced by the and . The DSCP is defined as the high-order six bits of the Service Type octet in the IP header. The parameter identifies the DSCP field and is an integer from 0 to 63. The commands to match IP DSCP, IP precedence, and IP TOS are alternative ways to specify a match criterion for the same Service Type field in the IP header, however each uses a different user notation. Format config acl rule match ipdscp 10-4 202-10009-01 ACL Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
10-4
ACL Commands
202-10009-01
config acl rule match dstl4port range
This command specifies a destination layer 4 port match condition for an ACL rule referenced by
the
<aclid>
and
<rulenum>
. The
<startport>
and
<endport>
parameters identify the first and
last ports that are part of the port range. They have values from 0 to 65535. The ending port must
have a value equal or greater than the starting port. The starting port, ending port, and all ports in
between will be part of the destination port range.
Either this command or the
config acl match destl4port keyword
command may be used to
specify a destination layer 4 port range as a match condition.
Format
config acl rule match dstl4port range <aclid> <rulenum> <startport>
<endport>
config acl rule match every
This command specifies a match condition in which all packets match for an ACL rule referenced
by the
<aclid>
and
<rulenum>.
The parameter
<true/false>
indicates to reinforce or negate
every match condition.
Format
config acl rule match every <aclid> <rulenum> <true/false>
config acl rule match ipdscp
This command specifies the IP DiffServ Code Point (DSCP) field for an ACL rule referenced by
the
<aclid>
and
<rulenum>.
The DSCP is defined as the high-order six bits of the Service Type
octet in the IP header. The
<dscpval>
parameter identifies the DSCP field and is an integer from
0 to 63.
The commands to match IP DSCP, IP precedence, and IP TOS are alternative ways to specify a
match criterion for the same Service Type field in the IP header, however each uses a different user
notation.
Format
config acl rule match ipdscp <aclid> <rulenum> <dscpval>