Netgear PS101 Reference Manual - Page 133

Appendix C CONFIG File

Get Netgear PS101 - Mini Print Server PDF manuals and user guides
UPC - 606449023442
View all Netgear PS101 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

NetGear Print Server Manual Appendix C CONFIG File This appendix provides information for editing a CONFIG file. CONFIG files are stored in the flash EEPROM of the NETGEAR PS100 series Print Sever and used for configuring the device using the FTP method. For more information about using the CONFIG file and to see an example of FTP commands, refer to the table of FTP Commands"on chapter 5 Unix. Only the parameters related to TCP/IP operation of the print server are listed. For modification of the various NetWare IPX/SPX and NetBEUI settings, NETGEAR recommends that you use the included NETGEAR Print Server Administration Program or the PSCONFIG program. CONFIG File TCP/IP Settings When modifying the CONFIG file, use the configuration settings outlined below. Configuration Settings Parameter and Command Definition Device Name (0001 BOX_NAME) The default name of the print server is PSxxxxxx (PS followed by 6 numbers). You can change this, but the new name must not exceed 19 characters and must not include any spaces. TCP/IP Protocol (0012 TCPIP_P) Enables or disables reception or transmission of TCP/IP packets. IP Address (4000 IP_ADDR) This is the IP address for your print server. For more information about IP addressing, refer to See Understanding IP Addresses." Device IP Address (4001 GATEWAY) If your network segment has a router, enter the router address here. If there is no router, leave the address as 0.0.0.0. Subnet Mask (4002 MASK) If the Gateway Address is 0.0.0.0, leave the Subnet Mask at 0.0.0.0. If you have a router, enter the Subnet mask for the segment to which the print server is attached. TCP Session Retry Interval (4010 TCP_INT) Sets how long the print server should wait before retrying a TCP/IP connection that is lost. Allowable values are from 0 to 255 seconds, with 2 as the default. Retry Count (4011 TCP_CNT) Sets how many attempts for reconnection will be made. After attempting the set number, the TCP/IP session is terminated. Allowable values are from 0 to 255, with 254 as the default. L1 Logical Printer Mapping (0100 L1_PROUT) The physical port that this L1 logical printer maps to. String Before Job for L1 Logical Printer (0101 L1_PREST) String After Job (0102 L1_POSTR) Convert LF to CR+LF (0103 L1_CHGLF) The L1 logical printer control string (in hex) to be sent to the printer before each print job. Note: A printer control string is limited to 15 characters. Examples are: ASCII = [Esc]&l0O Hexadecimal = 1B266C304F ASCII = [Esc]&l1O Hexadecimal = 1B266C314F The L1 logical printer control string (in hex) to be sent to the printer after each print job. Note: A printer control string is limited to 15 characters. Examples are: ASCII = [Esc]&l0O Hexadecimal = 1B266C304F ASCII = [Esc]&l1O Hexadecimal = 1B266C314F If On, LF (line feed) characters are changed to CR+LF (carriage return + line feed). If off, no conversion is done. 124

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
NetGear Print Server Manual
124
Appendix C CONFIG File
This appendix provides information for editing a CONFIG file. CONFIG files are stored in the flash
EEPROM of the NETGEAR PS100 series Print Sever and used for configuring the device using the
FTP method. For more information about using the CONFIG file and to see an example of FTP
commands, refer to the table of FTP Commands"on chapter 5 Unix. Only the parameters related to
TCP/IP operation of the print server are listed.
For modification of the various NetWare IPX/SPX and NetBEUI settings, NETGEAR recommends
that you use the included NETGEAR Print Server Administration Program or the PSCONFIG program.
CONFIG File TCP/IP Settings
When modifying the CONFIG file, use the configuration settings outlined below.
Configuration Settings
Parameter and
Command
Definition
Device Name
(0001 BOX_NAME)
The default name of the print server is PSxxxxxx (PS followed by 6 numbers). You can change
this, but the new name must not exceed 19 characters and must not include any spaces.
TCP/IP Protocol
(0012 TCPIP_P)
Enables or disables reception or transmission of TCP/IP packets.
IP Address
(4000 IP_ADDR)
This is the IP address for your print server. For more information about IP addressing, refer to
See
Understanding IP Addresses
."
Device IP Address
(4001 GATEWAY)
If your network segment has a router, enter the router address here. If there is no router, leave the
address as 0.0.0.0.
Subnet Mask
(4002 MASK)
If the Gateway Address is 0.0.0.0, leave the Subnet Mask at 0.0.0.0. If you have a router, enter
the Subnet mask for the segment to which the print server is attached.
TCP Session Retry
Interval
(4010 TCP_INT)
Sets how long the print server should wait before retrying a TCP/IP connection that is lost.
Allowable values are from 0 to 255 seconds, with 2 as the default.
Retry Count
(4011 TCP_CNT)
Sets how many attempts for reconnection will be made. After attempting the set number, the
TCP/IP session is terminated. Allowable values are from 0 to 255, with 254 as the default.
L1 Logical Printer
Mapping
(0100 L1_PROUT)
The physical port that this L1 logical printer maps to.
String Before Job for L1
Logical Printer
(0101 L1_PREST)
The L1 logical printer control string (in hex) to be sent to the printer before each print job. Note: A
printer control string is limited to 15 characters.
Examples are:
ASCII = [Esc]&l0O
Hexadecimal = 1B266C304F
ASCII = [Esc]&l1O
Hexadecimal = 1B266C314F
String After Job
(0102 L1_POSTR)
The L1 logical printer control string (in hex) to be sent to the printer after each print job. Note: A
printer control string is limited to 15 characters.
Examples are:
ASCII = [Esc]&l0O
Hexadecimal = 1B266C304F
ASCII = [Esc]&l1O
Hexadecimal = 1B266C314F
Convert LF to CR+LF
(0103 L1_CHGLF)
If On, LF (line feed) characters are changed to CR+LF (carriage return + line feed). If off, no
conversion is done.