NordicTrack E400 Instruction Manual - Page 8

Tip: Have

Get NordicTrack E400 PDF manuals and user guides View all NordicTrack E400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Tip: Avoid pinching the wires. Slide the Upright (4) onto the Frame (1). Tip: Have a second person hold the Lower Upright Cover (58) out of the way. Attach the Upright (4) with four M8 x 16mm Screws (53), four M8 Split Washers (18), and four M8 Washers (12); do not fully tighten the Screws yet. Then, slide the Lower Upright Cover (58) downward; do not press the Lower Upright Cover into place yet. 5 Avoid pinching the wires 4 58 53 18 18 53 12 12 18 53 1 6. Insert the Long Axle (56) into the Upright (4) and center it. Then, slide a Wave Washer (21) (only one is shown) onto each side of the Long Axle. Tip: It may be helpful to use a rubber mallet. Next, slide the two Upper Body Legs (7) onto the right and left sides of the Long Axle (56). Attach the right Upper Body Leg (7) with an M10 x 20mm Screw (26), an M10 Split Washer (25), an M10 Washer (59), and a D-washer (24); do not fully tighten the Screw yet. Attach the left Upper Body Leg (7) in the same way. Then, tighten both M10 x 20mm Screws (26) at the same time. 6 26 7 4 56 21 24 59 25 26 7 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
5.
Tip: Avoid pinching the wires.
Slide the
Upright (4) onto the Frame (1).
Tip: Have a
second person hold the Lower Upright Cover
(58) out of the way.
Attach the Upright (4) with four M8 x 16mm
Screws (53), four M8 Split Washers (18), and
four M8 Washers (12);
do not fully tighten the
Screws yet.
Then, slide the Lower Upright Cover (58)
downward;
do not press the Lower Upright
Cover into place yet.
5
1
53
53
53
18
18
18
12
12
Avoid pinching
the wires
56
21
24
59
25
26
26
6
7
4
7
4
58
6.
Insert the Long Axle (56) into the Upright (4) and
center it. Then, slide a Wave Washer (21) (only
one is shown) onto each side of the Long Axle.
Tip: It may be helpful to use a rubber mallet.
Next, slide the two Upper Body Legs (7) onto the
right and left sides of the Long Axle (56).
Attach the right Upper Body Leg (7) with an
M10 x 20mm Screw (26), an M10 Split Washer
(25), an M10 Washer (59), and a D-washer (24);
do not fully tighten the Screw yet.
Attach the left Upper Body Leg (7) in the
same way.
Then, tighten both M10 x 20mm Screws (26)
at the same time.