Oki ML186 OKI MICROLINE 186 User's Guide - Page 59

want printing to start. Many word processing packages

Get Oki ML186 PDF manuals and user guides View all Oki ML186 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

10. Pull the paper lever (right side of printer) toward the front of the printer-to the continuous forms position-and make sure the paper is straight by adjusting it to align the left and right sides behind the platen with the sides in front of the platen. Important Be sure that the paper covers the groove in the left end of the platen so that it clears the paper out detector. 11. Push the paper lever back to the single sheet position to reapply pressure on the platen. 12. Push the bail arm lever (left side of printer) back to close the bail arm. 13. Replace the access cover: a. Fit the cover tabs into the slots at the printer front. b. Lower the cover carefully, making sure the paper fits through the front slot in the access cover. 14. Lower the paper separator so that paper enters the printer from under the separator and exits the printer going over the separator (see "Correct Paper Path" diagram on page 56). 15. Turn the platen knob to move the paper to the point where you want printing to start. (Many word processing packages automatically allow for a top margin of 1 inch [25 mm]). Note To save this position as the permanent Top of Form, press the TOF button. 59 • Operating Your Printer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
59
•
Operating Your Printer
10.Pull the paper lever (right side of printer) toward the front of the
printer—to the continuous forms position—and make sure the
paper is straight by adjusting it to align the left and right sides
behind the platen with the sides in front of the platen.
11. Push the paper lever back to the single sheet position to
reapply pressure on the platen.
12.Push the bail arm lever (left side of printer) back to close the
bail arm.
13.Replace the access cover:
a. Fit the cover tabs into the slots at the printer front.
b.Lower the cover carefully, making sure the paper fits through
the front slot in the access cover.
14.Lower the paper separator so that paper enters the printer
from under the separator and exits the printer going over the
separator (see “Correct Paper Path” diagram on page 56).
15.Turn the platen knob to move the paper to the point where you
want printing to start. (Many word processing packages
automatically allow for a top margin of 1 inch [25 mm]).
Important
Be sure that the paper covers the groove in the left end of the
platen so that it clears the paper out detector.
Note
To save this position as the permanent Top of Form,
press the TOF button.