Onkyo TX-8390 User Manual English - Page 69

Playing Back, Output Assign - TV Out / OSD - Zone 2 HDMI

Get Onkyo TX-8390 PDF manuals and user guides View all Onkyo TX-8390 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Playing Back Contents ≫ Connections ≫ Playback ≫ Setup ≫ When operating with the remote controller, perform the following procedure when the unit is on. 1. Press REMOTE MODE ZONE 2. • The remote controller switches to the mode for controlling ZONE 2. 2. Face the remote controller at this unit and press . On the main unit, after pressing ZONE 2, within 8 seconds turn the INPUT SELECTOR dial to select the input to be played in the separate room. To play the same source in the main room and separate room, press ZONE 2 on the main unit twice. • "Z2" on the display of the main unit lights up. 3. Adjust the volume on the pre-main amplifier for the separate room. • If you turn the unit to standby during multi-zone playback, the Z2 indicator is dimmed, and the playback mode is switched to playback in a separate room only. Setting ZONE 2 to on while the unit is in standby also switches the playback mode to playback in the separate room only. • The audio from externally connected AV components can be output to ZONE 2 only when the audio is analog or 2ch PCM signal. When the AV component is connected to this unit with an HDMI cable, digital coaxial cable or digital optical cable, change the audio output of the AV component to the PCM output. • When video and audio via HDMI input are output to ZONE 2, set "1. Input/ Output Assign" - "TV Out / OSD" - "Zone 2 HDMI" ( p81) to "Use" on the Setup menu. • DSD audio signals cannot be output to ZONE 2 with the "NET" input selector. • If ZONE 2 is on, power consumption during standby will increase. • If ZONE 2 is turned on when the Pure Audio listening mode is selected in the main room, the mode will automatically switch to the Direct listening mode. To turn off the function: Press the button while the remote controller is in the mode for controlling ZONE 2. Alternatively press OFF on the main unit. 69 Front Panel≫ Rear Panel≫ Remote≫

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
69
Front Panel
≫
Rear Panel
≫
Remote
≫
Contents
≫
Connections
≫
Playback
≫
Setup
≫
Playing Back
When operating with the remote controller, perform the following procedure when
the unit is on.
1. Press REMOTE MODE ZONE 2.
• The remote controller switches to the mode for controlling ZONE 2.
2. Face the remote controller at this unit and press
. On the main unit, after
pressing ZONE 2, within 8 seconds turn the INPUT SELECTOR dial to select
the input to be played in the separate room. To play the same source in the
main room and separate room, press ZONE 2 on the main unit twice.
•
"Z2" on the display of the main unit lights up.
3.
Adjust the volume on the pre-main amplifier for the separate room.
• If you turn the unit to standby during multi-zone playback, the Z2 indicator is
dimmed, and the playback mode is switched to playback in a separate room
only. Setting ZONE 2 to on while the unit is in standby also switches the
playback mode to playback in the separate room only.
•
The audio from externally connected AV components can be output to ZONE
2 only when the audio is analog or 2ch PCM signal. When the AV component
is connected to this unit with an HDMI cable, digital coaxial cable or digital
optical cable, change the audio output of the AV component to the PCM
output.
• When video and audio via HDMI input are output to ZONE 2, set "1. Input/
Output Assign" - "TV Out / OSD" - "Zone 2 HDMI" (
p81
) to "Use" on the
Setup menu.
• DSD audio signals cannot be output to ZONE 2 with the "NET" input selector.
• If ZONE 2 is on, power consumption during standby will increase.
• If ZONE 2 is turned on when the Pure Audio listening mode is selected in the
main room, the mode will automatically switch to the Direct listening mode.
To turn off the function:
Press the
button while the remote controller is in the
mode for controlling ZONE 2. Alternatively press OFF on the main unit.