Onkyo TX-L50 User Manual English - Page 58
Level Calibration, Dolby Enabled Speaker, Equalizer Settings
View all Onkyo TX-L50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 58 highlights
> Before Start > Part Names > Install > Initial Setup > Playback Supplementary Information | Advanced Setup | Others ˙ 4. Level Calibration Front Left Center Front Right Height Left Height Right Surround Right Surround Left Subwoofer Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. (Default Value is "0 dB") Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. (Default Value is "0 dB") Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). Select a value between "j12 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). Select a value between "j15 dB" and "i12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level (Default Value is "0 dB"). ∫ 5. Dolby Enabled Speaker E N Dolby Enabled Set the distance between the Dolby enabled speaker and the Speaker to Ceiling ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/ 4.50 m" (in 0.1 ft/0.03 m increments, default value is "1.80 m") 0 The unit of distance (feet/meters) shown is the unit selected for use in "Distance". AccuReflex You can enhance the reflection effect of Dolby enabled speaker from the ceiling. "On": When this function is to be used "Off (default value)": When this function is not to be used 0 The function is not effective if the listening mode is Direct. 0 This setting can only be selected when you have set "Configuration" - "Height Speaker" to "Dolby Speaker". ˙ 6. Equalizer Settings You can adjust the output volume of the range of each connected speaker. You can adjust the volume of the different sound ranges for each of the speakers. You can set three different equalizers in Preset 1 to 3. You can select up to 5 bands for the Subwoofer and 9 bands for all other speakers. To use the set equalizer effects, select the preset number in "QUICK MENU"- "AccuEQ" - "Equalizer" (ÄP50). Front Center Height After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors W/X, adjust the volume of that frequency between "j6.0 dB" and "i6.0 dB" with S/T. (Default Value is "0.0 dB") After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors W/X, adjust the volume of that frequency between "j6.0 dB" and "i6.0 dB" with S/T. (Default Value is "0.0 dB") After selecting the speaker frequency from between "25 Hz" and "16 kHz" with the cursors W/X, adjust the volume of that frequency between "j6.0 dB" and "i6.0 dB" with S/T. (Default Value is "0.0 dB") 58