Panasonic AG-HMC80PJ Basic Operating Instructions - Page 33

Using as a LCD monitor, Emphasizing outlines, Select EVF DTL and press the ENTER

Get Panasonic AG-HMC80PJ PDF manuals and user guides View all Panasonic AG-HMC80PJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Basic Operations Using as a LCD monitor Open the eye piece to use as a LCD monitor. Opening the eye piece Open the eye piece while pressing the lock button at the same time. Eye piece Lock button Emphasizing outlines When EVF DTL is assigned to one of the USER buttons 1 to 3, you can press that button to emphasize the outlines of images in the viewfinder and make focus alignment easier. Emphasizing the outlines does not effect the images you shoot. 1 Set the POWER switch to ON. (Page 30) 2 Press the MENU button. • Menu operation (Page 40) • Operations may also be performed using buttons on the remote control that correspond to those on the camera. For details, see "Description of parts (Remote control)". (Page 23) 3 Select either the USER1 SW, USER2 SW or the USER3 SW item in the setting menu SW&DISP SETUP screen, and press the ENTER button. 4 Select EVF DTL and press the ENTER button. EVF DTL is assigned to the selected USER button. Closing the eye piece Close the eye piece by pressing it until it clicks into place. • Rotating the viewfinder with the eye piece open may result in damage to the eye piece or your fingers getting caught. 5 In CAMERA mode or PHOTO mode, press the USER button assigned to EVF DTL. "EVF DTL ON" appears in the center of the screen for about 2 seconds. To release the setting, press the USER button assigned to EVF DTL again, and "EVF DTL OFF" appears in the center of the screen for approximately 2 seconds. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
33
Basic Operations
Using as a LCD monitor
Open the eye piece to use as a LCD monitor.
Opening the eye piece
Open the eye piece while pressing the lock button
at the same time.
Eye piece
Lock button
Closing the eye piece
Close the eye piece by pressing it until it clicks into
place.
Rotating the viewfinder with the eye piece
open may result in damage to the eye piece or
your fingers getting caught.
•
Emphasizing outlines
When EVF DTL is assigned to one of the USER
buttons 1 to 3, you can press that button to
emphasize the outlines of images in the viewfinder
and make focus alignment easier.
Emphasizing the outlines does not effect the
images you shoot.
1
Set the POWER switch to ON. (Page 30)
2
Press the MENU button.
Menu operation (Page 40)
Operations may also be performed
using buttons on the remote control that
correspond to those on the camera. For
details, see “Description of parts (Remote
control)”. (Page ±3)
3
Select either the USER1 SW, USER2 SW
or the USER3 SW item in the setting menu
SW&DISP SETUP screen, and press the
ENTER button.
4
Select EVF DTL and press the ENTER
button.
EVF DTL is assigned to the selected USER
button.
5
In CAMERA mode or PHOTO mode, press
the USER button assigned to EVF DTL.
“EVF DTL ON” appears in the center of the
screen for about ± seconds.
To release the setting, press the USER button
assigned to EVF DTL again, and “EVF DTL
OFF” appears in the center of the screen for
approximately ± seconds.
•
•