Panasonic AG-HPX370 AGHPX370P User Guide - Page 35

Basic Procedures

Get Panasonic AG-HPX370 PDF manuals and user guides View all Panasonic AG-HPX370 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Chapter 3 Recording and Playback Basic Procedures This section describes the basic procedure for shooting and recording. Before you embark on a shoot, pre-inspect your system to ensure that it works properly. For directions on inspecting your memory card camerarecorder, see [Inspections Before Shooting] (page 157). Battery Set-up to P2 card Insertion Note that the recording order is retained even if the power is turned off. When the power is next turned on, the last card written before powering-down will be the target card. 1 Insert a charged battery. 2 Turn the POWER switch to ON to check the battery remaining level in the viewfinder. • When battery capacity is low, replace it with a fully charged battery.  NOTE When low battery capacity is indicated after replacing a battery with a fully charged battery, check battery installation. For details, refer to [BATTERY SETUP screen] (page 144). 3 Insert a P2 card, check that the P2 CARD ACCESS LED lights orange or green before closing the slot cover. • When more than one P2 card slot contains a P2 card, the card in the slot with the lowest number is used first. However, regardless of slot number, a P2 card inserted later will not be accessed until the other cards have been used. Example: If the two slots contain P2 cards, the cards are used in order of slot numbers 12. However, if the P2 card in Slot 1 is removed and then reinserted, the cards will be used in the following order: 21. 1 2 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
³5
Chapter²³² Recording²and²Playback
Basic Procedures
This section describes the basic procedure for shooting
and recording.
Before you embark on a shoot, pre-inspect your system to
ensure that it works properly.
For directions on inspecting your memory card camera-
recorder, see [Inspections Before Shooting] (page 157).
Battery Set-up to P2 card Insertion
1
²
Insert²a²charged²battery.
2
²
Turn²the²POWER²switch²to²ON²to²check²the²
battery²remaining²level²in²the²viewfinder.
• When battery capacity is low, replace it with a fully
charged battery.
NOTE
When low battery capacity is indicated after replacing
a battery with a fully charged battery, check battery
installation.
For details, refer to [BATTERY SETUP screen] (page 144).
3
²
Insert²a²P±²card,²check²that²the²P±²CARD²
ACCESS²LED²lights²orange²or²green²before²
closing²the²slot²cover.
• When more than one P2 card slot contains a P2
card, the card in the slot with the lowest number
is used first. However, regardless of slot number,
a P2 card inserted later will not be accessed until
the other cards have been used.
Example:
If the two slots contain P2 cards, the cards are
used in order of slot numbers 1
2. However, if
the P2 card in Slot 1 is removed and then re-
inserted, the cards will be used in the following
order: 2
1.
1
2
Note that the recording order is retained even if the power
is turned off. When the power is next turned on, the last
card written before powering-down will be the target card.