Panasonic WJ-HD616/1000 Installation Guide

Panasonic WJ-HD616/1000 Manual

Get Panasonic WJ-HD616/1000 PDF manuals and user guides View all Panasonic WJ-HD616/1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic WJ-HD616/1000 manual content summary:

  • Panasonic WJ-HD616/1000 | Installation Guide - Page 1
    Installation Guide Digital Disk Recorder Model No. WJ-HD616K WJ-HD716K ERROR SAULSAPREMND TIMER OPERATE ALARM ARLEASREMT STS HDD1 A/F HDD2 to connect or operate this product, please read these instructions carefully and save this manual for future use. No model number suffix is shown in this
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 2
    the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Power disconnection. Unit , if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 3
    USER; (4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT; (5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY; (6) ANY CLAIM
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 4
    block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators . 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 5
    Contents Limitation of liability 3 Disclaimer of warranty 3 Important safety instructions 4 Preface 7 Features 7 System configuration 8 About the user manuals 9 System requirements for a PC 9 Trademarks and registered trademarks 10 Copyright 10 Abbreviations 10 Network security 11
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 6
    Error recovery of the hard disk drive (when operating in the RAID mode 145 Replacement of a faulty hard disk drive in the RAID mode 146 Troubleshooting 147 Check the power cord, connector and plug periodically 152 Specifications 153 Standard accessories 154 Optional Accessories 154 6
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 7
    16 cameras on the hard disk drives. This product supports HDMI (High-Definition Multimedia Interface) standard which allows displaying will become more sensitive using the depth compensation. Refer to the operating instructions of cameras for further information about the i-VMD function. • Save and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 8
    SDHC/SD memory card slot Images being captured at an alarm occurrence or at a network error can be saved on a SDHC/SD memory card (option) automatically. It is also possible to directly save images on a SDHC/SD memory card. Images saved on the SDHC/SD memory card can be played or downloaded using a
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 9
    About the user manuals The following 3 manuals are provided for the WJ-HD616K / WJ-HD716K. Installation Guide (this document): Contains descriptions of how to install/connect this product and how to configure the required settings. Operating Instructions (PDF): Contains descriptions of how to
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 10
    Other names of companies and products contained in these operating instructions may be trademarks or registered trademarks of their respective owners. is prohibited. Abbreviations The following abbreviations are used in this manual. Microsoft® Windows Vista® Business SP1 (32-bit) is described
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 11
    Network security As you will use this product connected to a network, your attention is called to the following security risks. q Leakage or theft of information through this product w Use of this product for illegal operations by persons with malicious intent e Interference with or stoppage of this
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 12
    disk failures. • When hard disk drive trouble occurs, replace it immediately. Contact your dealer about servicing. SDHC/SD memory card • When work correctly or performance of this product may be deteriorated. Refer to Operating Instructions (PDF) for how to format a SDHC/SD memory card. • When
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 13
    Cleaning • Turn the power off, and then use a soft cloth to clean this product. When the dirt is hard to remove, use a mild detergent and wipe gently. Wipe out the detergent completely using a soft cloth. • Do not use strong or abrasive detergents when cleaning the body. • When using a chemical
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 14
    Precautions for Installation This product is designed for indoor use. Avoid the following locations for installation. • Locations exposed to direct sunlight • Places subject to having strong vibration or impact • Near magnetic field sources such as a television or speakers • Place where
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 15
    37 mm ø1.32 mm - ø1.37 mm ø0.13 mm - ø0.69 mm Important: • A cøo0.m13pmatmibl-eøp0.lu69g mshmall be used. Failure to observe this may cause trouble such as poor contact. At worst, the connector of this product may be damaged. Avoid placing receptacles that contain liquids such as water near this
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 16
    ERROR: Blinks when an error that can become a problem for the recorder to run the system occurs. Blinks alarm suspension mode is selected. (☞ Operating Instructions (PDF)) TIMER: Lights when the schedule recording (for more than 2 seconds) during manual recording. Lights orange: During recording t
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 17
    to determine the edited settings on the setup menu. This button also can be used to turn the alarm suspension on/off. (☞ Operating Instructions (PDF)) !3 Mouse connection port [MOUSE] Use this port to connect a USB mouse (commercially available). (No device other than a mouse can be connected
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 18
    clicks and pull it up straight. Eject button Note: • After copying the recorded data on a DVD, perform the procedure to eject the DVD. (☞ Operating Instructions (PDF)) Otherwise, the tray may not open even after the eject button is pressed. Step 3 Place a disc with the label side up and fit
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 19
    Step 4 Push the tray to the end. Click sound will be heard and the tray will be fixed. Step 5 Close the DVD drive cover. Important: • When opening/closing the DVD drive tray, do not apply force on the tray. • When not using the DVD drive, close the disc tray. • When removing the disc from the tray,
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 20
    Behind the front cover Refer to page 21 for descriptions of how to detach the front cover. qw e ALARM USE RESET ERROR ALARM RAID ALARM SUSPEND STS HDD 1 A/F TIMER HDD 2 HDD 3 OPERATE HDD 4 ESC SET t r STS A/F STS A/F STS A/F STS A/F MAINTENANCE MOUSE y ui o q Use button [
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 21
    How to detach the front cover Step 1 (When detaching the front cover while the power is on) Hold down the [ALARM RESET] button and the [MONITOR] button (for more than 2 seconds). → The power of the front cover will be turned off. Step 2 Open the maintenance port cover and the DVD drive cover, and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 22
    Note: • After attaching the front cover to the recorder, be sure to turn on the power of front cover. ■ Rear view q w er t yu IN OUT EXT STORAGE MODE DATA RS485(CAMERA) 10/100BASE-T 3 2 ALARM ALARM/CONTROL 1 1 MONITOR OUT 2 OUT-CASCADE-IN 12345678 2 2 1 2 1 CASCADE IN OUT
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 23
    !4 Monitor output connector (BNC) [MONITOR OUT 1, 2] Connect a monitor to this connector. Monitor output connector 1 shall be used to connect a monitor (Monitor 1) to display live image only. Monitor output connector 2 shall be used to connect a monitor (Monitor 2) to display live/recorded images
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 24
    is operated via a network). When operating the recorder directly Operate the recorder while monitoring the monitor connected to the recorder. There are 3 ways of how to operate the recorder directly. • Operate using the buttons on the front cover of the recorder. • Operate using a mouse connected
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 25
    Note: • When operating from a system controller compatible with PS·Data, log in to the recorder automatically as the user registered in "PSD user" on the "Basic" tab under "User mng.". • When no operation is made for approx.2 minutes after logging in from a system controller compatible with PS·Data,
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 26
    To directly operate the recorder, there are 2 ways of how to operate it: operations using the buttons assigned to each button. Refer to Operating Instructions (PDF) for how to operate each function. When you find "Select XX button" in the operating instructions, move the cursor onto the XX button
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 27
    Operations flow The operation flow of the recorder is as follows. z Rack mounting (☞ Page 28) x Connections (☞ Page 29) c Installation of the hard disk drives (☞ Page 52) v Determination of the operational mode (☞ Page 54) b Startup (☞ Page 55) n Configuration of the settings for
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 28
    Rack mounting Install the recorder in an EIA standard rack. Equivalent to EIA standard rack (not manufactured by Panasonic): EIA 19-inch rack type (Depth: 550 mm or more) Note: • Use four M5 x 12 screws (locally procured) to install the recorder in a rack. Step 1 Remove the five rubber feet
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 29
    Connections Connection of cameras Up to 16 cameras (system cameras or combination cameras) can be connected to the video input connector 1-16. Important: • When using with a Panasonic's matrix switcher or a coaxial communication unit, make sure that the loop-through output connection (of each video
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 30
    Connection of monitors Connect monitors to the monitor output connector. Connect a monitor to be used to display live images only to the monitor output connector 1. Connect a monitor to be used to display not only live images but also recorded images and setup menu to the monitor output connector 2.
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 31
    When connecting a monitor using a HDMI cable Monitor 2 Monitor 1 HDMI cable (locally procured) IN OUT EXT STORAGE MODE DATA RS485(CAMERA) 10/100BASE-T 3 2 ALARM ALARM/CONTROL 1 1 MONITOR OUT 2 OUT-CASCADE-IN 12345678 2 2 1 2 1 CASCADE IN OUT MONITOR OUT(HD) 1 3 1 IN CASCADE
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 32
    Connection of a PC Connect a PC and the recorder. Required devices and cables vary depending on how to connect them. Before starting the connection, prepare the required devices and cables. Connect a PC and the recorder directly Use a LAN cable to connect a PC and the recorder directly. Recorder
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 33
    the extension unit. Fix the connection cable Fix the connection cable Attach the cable clamp to each connection cable. Refer to the operating instructions of the extension unit for how to attach the cable clamp. IN OUT EXT STORAGE MODE DATA 3 2 3 ALARM 1 2 11 MONITOR OUT 2 ALARM/CONTROL
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 34
    Connection of a VCR When copying images recorded on the recorder to a VCR, connect cables from a VCR to the video output connector and the audio connector inside the SDHC/SD memory card slot cover at the front of the recorder. VCR AUDIO IN Audio cable with plugs (locally procured) VIDEO IN Video
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 35
    compatible system controller. Important: • Select "On" for the termination setting of the devices on both ends of the connection. Refer to the operating instructions of each device on both ends of the connection. The termination setting of the recorder can be set using the mode switch. (☞ Page 51
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 36
    When connecting the recorder between a system controller and a system device POWER ON OFF UNIT 1 ALARM RESE T SUSPEND SET UP SE T ESC ALARM ALARM SUSPEND 2 3 4 Data Multiplex Unit WJ-MP204 Coaxial communication unit Termination: On Unit address: 2 RS485 cable (WV-CA48/50) Mode
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 37
    Cascading connection of multiple recorders Up to 5 recorders can be connected in cascading connection. When connecting recorders in cascading connection, images displayed on Monitor 2 connected to the second and subsequent recorders can be switched and displayed on Monitor 2 connected to the first
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 38
    Cascading connection using HDMI cables Important: • Up to 5 recorders and a single system controller can be connected. • Connect the recorder whose unit address (system) is even number to the cascade input 1 connector of the first recorder. Connect the recorder whose unit address (system) is odd
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 39
    Connection of PS·Data compatible devices When connecting a PS·Data compatible system controller to the first recorder Mode switch ON 123456 78 (No.7: OFF) (No.8: OFF) RS485 cable (provided with the controller) IN OUT EXT STORAGE MODE DATA RS485(CAMERA) 10/100BASE-T 3 2 ALARM ALARM/
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 40
    When connecting a PS·Data compatible system controller to the third recorder Mode switch ON 123456 78 (No.7: OFF) (No.8: ON) IN OUT EXT STORAGE MODE DATA RS485(CAMERA) 10/100BASE-T 3 2 ALARM ALARM/CONTROL 1 1 MONITOR OUT 2 OUT-CASCADE-IN 12345678 2 2 1 2 1 CASCADE IN OUT MONITOR
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 41
    When connecting PS·Data compatible system controllers to both the first and the third recorders Mode switch ON 123456 78 (No.7: OFF) (No.8: OFF) RS485 cable (provided with the controller) Controller Termination: On Unit address: 1 IN OUT EXT STORAGE MODE DATA RS485(CAMERA) 10/100BASE-T
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 42
    Connection of RS485 cameras The following are examples when connecting RS485 cameras to the recorder. Up to 8 RS485 cameras can be connected to a single RS485 port. Important: • Select "On" for the termination setting of the devices on both ends of the connection. The termination setting of the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 43
    GND Unit number 11 Termination: Off Unit number 9 Termination: Off Unit number 12 Termination: On Unit number 10 Termination: Off Combination camera (RS485) Combination camera (Supporting coaxial communication) 43
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 44
    About the connectors How to use the terminals of the ALARM/CONTROL connector These terminals are used for emergency recording, auto time adjustment and when installing a buzzer, a lamp or a similar alarm device. The connector to be used should be compatible with the pin array. 13 1 Pin array
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 45
    Connection for emergency recording When the external switch is turned on, emergency recording will start. Emergency recording will differently be performed depending on the settings on the [Emergency rec.] tab under the "Basic" page of the setup menu. (☞ Page 70) (Signal ground) (Emergency
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 46
    Connection for the auto time adjustment function (1) When "Master" is set for "Auto time adjustment" on the [Time & date] tab under the "Basic" page of the setup menu "Time adjustment signal output" becomes available and the clock of this recorder will be applied to other devices. The time
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 47
    be suspended. Recorder 13 (Signal ground) (Outage detection input) (Outage processing end output) (Signal ground) (Detection) (Shutdown) * Refer to the operating instructions of the UPS in use for how to connect the UPS. 23 19 ALARM/CONTROL Power cord Uninterruptible Power System (UPS) To
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 48
    How to use the terminals of the ALARM connector These terminals are used to connect the alarm devices, such as sensors, door switches, etc. The connector to be used should be compatible with the pin array. 13 1 Pin array The pin array is different from other digital disk recorders. Make sure
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 49
    Alarm connection When a signal is supplied to the alarm input terminals 1 - 16 (pin nos. 1 - 8, 15 - 22 of the ALARM connector), recording and displaying of images from the cameras will be performed according to the settings. When an alarm device such as a buzzer, a lamp, etc., is installed outside,
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 50
    Time and polarities of the ALARM/CONTROL terminal and the ALARM terminal Terminal Alarm input Alarm output Alarm reset input Emergency recording input Available disk space warning output HDD error output Camera error output Error output Time adjustment I/O Alarm suspension input External recording
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 51
    Mode switch Communication between the recorder and a system device using PS·Data can be performed by RS 485 interface. Devices on both ends of the RS485 connection are necessary to be terminated. The mode switch setting differs depending on whether to use the recorder as a receiver or a system
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 52
    the disk slot number. (1) Lift the lever on the HDD unit while holding down the removal knob, and then insert the HDD unit all the way into the HDD slot. Removal knob of the HDD unit Lever (2) Pinch the rim on the HDD slot with the hook on the HDD unit
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 53
    Note: • Hard disk drives are locally procured. Contact your deal- er for purchasing, installing, and replacing the hard disk drives. • Refer to the operating instructions of the extension unit for how to install the HDD units on the extension unit. Remove the HDD unit Step 1 Remove the HDD unit
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 54
    the recorder with the RAID function that is known as the HDD fault-tolerance system by installing an optional RAID board. Refer to the operating instructions of the RAID board for how to install the RAID board. The following operational modes are provided to the RAID function of the recorder. RAID
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 55
    after turning on the power of the server. Currently recorded images are being played Step 1 Press this button to stop playback. (☞ Operating Instructions (PDF)) Step 2 Turn off the power of the recorder after confirming that all the HDD access indicators (A/F (HDD access/failure)) are off
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 56
    Configure the minimum settings required to use the recorder Configure the minimum settings required to use the recorder such as the time and date setting, the language setting, the settings relating to recording and the schedule settings on the "Quick" page of the setup menu. Refer to page 59 for
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 57
    Setup menu Configuration of each setting item in the setup menu should be completed in advance to use this recorder. The operations in the setup menu are performed with either of the following: • Displaying the setup menu on Monitor 2 by using buttons on the front cover or a mouse connected to the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 58
    About Setup menu q w e r t y u !3 i o !0 !1 !2 q [Quick] button Select this button to display the "Quick" page (☞ page 63). The minimum settings required to operate the recorder such as the time & date, language, recording schedule, etc. can be configured on the "Quick" page. w
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 59
    !1 [Maintenance] button Select this button to display the "Maintenance" page (☞ page 119). Check and setup of the hard disk drive information of the recorder, management of the setup data and check of log information can be carried out on the "Maintenance" page. Formatting SD memory cards and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 60
    Operation using buttons on the front cover Step 2 SET Select the desired setup menu. Press the [SET] button after moving the cursor to the desired setup menu using the arrows button (C D A B). Operation using a mouse connected to the recorder Step 2 Select the desired setup menu. Put the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 61
    Operation using buttons on the front cover Step 4 Configure each setting item. Selection of setting item Press the [SET] button after moving the cursor to the desired item using the arrows button (C D A B). Display of advanced setup pop-up page Move the cursor to "Setup" of the setting item, and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 62
    Step 5 SET ESC Holding down (for more than 2 seconds) Apply the settings to the recorder, and exit the setup menu. Hold down the [SETUP/ESC] button for 2 seconds or more. → T he monitor display will return to live imag- es. or Press the [SET] button after moving the cur- sor to the [Exit]
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 63
    Configure the minimum settings required to operate the recorder [Quick] The minimum settings required to operate the recorder such as the language, time & date, network and schedule, etc. can be configured on the "Quick" page. The "Quick" page has only the [Setup] tab. First, configure the minimum
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 64
    [Rate(ips)] Adjusts the recording rate. Off/1.25ips/2.5ips/3.75ips/7.5ips/15ips/30ips (Only for HD716K) Default: 15ips (30ips for WJ-HD716K) [Display] button The time table of the schedule set on this page will be displayed on the pop-up window. [OK] button The selected resolution and the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 65
    Configure the basic settings of the recorder [Basic] The basic settings of the recorder such as time & date, recording actions and audio, etc. and the settings relating to the emergency recording can be configured on the "Basic setup" page. The "Basic" page has [Basic], [Time & date], [Recording], [
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 66
    Configure the settings relating to time & date [Time & date] Select the [Time & date] tab on the "Basic" page. (☞ Page 60) The settings relating to time & date display can be configured on this tab. [Date display format] Select a date display format. (Example: April 1, 2009) YY/MM/DD: 09/04/01
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 67
    the entry field. On-screen keyboard (for time & date entry) will be displayed, and it is possible to enter the time & date. Refer to Operating Instructions (PDF) for further information about how to use the on-screen keyboard. Up to 10 times and dates for switching to summer time can be
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 68
    is selected for this setting, no recordings will be performed. Select "On" for normal use except when required to stop recording forcibly such as when a problem occurred with the recorder. Note: • It is possible to select "On" or "Off" to determine whether or not to display the camera title or the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 69
    Configure the settings relating to audio [Audio] Select the [Audio] tab on the "Basic" page. (☞ Page 60) The audio inputs from the AUDIO IN connectors (1 to 4) on the rear panel of the recorder can be assigned to the selected camera channels, and reception interval can be configured on this tab.
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 70
    rate can be configured on this tab. Refer to Operating Instructions (PDF) for further information about the emergency recording. [Resolution s/5 s/10 s/20 s/30 s/1 min/3 min/5 min/10 min/30 min Manual: Recording will continue while the external switch is being held down. Recording will be
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 71
    output is supplied. 2s/5s/10s/20s/30s/1min Ext: Alarm output will continue until the alarm action is reset. Refer to the operating instructions (PDF) for further information about alarm reset. Rec: The alarm output will be supplied during event recording is being performed. Default: 2s Note: • No
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 72
    the [Terminal/Command] tab on the "Event" page. (☞ Page 60) The settings relating to event actions to be taken at a terminal alarm (☞ Operating Instructions (PDF)) occurrence can be configured on this tab. [Operation mode] Select the settings for the operation mode. Refer to the operating
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 73
    ] Select the [Site alarm] tab on the "Event" page. (☞ Page 60) The settings relating to event actions to be taken at a camera site alarm (☞ Operating Instructions (PDF)) occurrence can be configured on this tab. [Operation mode] Select the settings for the operation mode. Refer to the operating
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 74
    loss] Select the [Video loss] tab on the "Event" page. (☞ Page 60) The settings relating to event actions to be taken at a video loss (☞ Operating Instructions (PDF)) occurrence can be configured on this tab. [Operation mode] Select the settings for the operation mode. Refer to the operating
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 75
    a VMD occurrence [VMD] Select the [VMD] tab on the "Event" page. (☞ Page 60) The settings relating to event actions to be taken at a VMD (☞ Operating Instructions (PDF)) occurrence can be configured on this tab. [Operation Mode] Select the settings for the operation mode. Refer to the operating
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 76
    can be set. Up to 4 areas can be set for a camera channel for the detection area.Details on video motion detection are given on Operating Instructions (PDF). [Area] button Configure the settings for each camera channel (1 to 16). (☞ Page 77) 76
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 77
    Settings for the video motion detection function Configure the settings for video motion detection areas for each camera channel. Up to 4 areas can be set for a camera channel for the detection area. When selecting "On" for "Search" on the [VMD] tab and selecting "Area", a detection area setup page
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 78
    Step 3 Set the end point of the detection area. Press the [SET] button after moving the cursor to the desired end point of the detection area using the arrows button (C D A B). To finish the detection area setting, select the [Back] button. Step 5 Select the [Back] button after completing the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 79
    Configure the settings relating to recording/event schedules [Schedule] The settings for the recording schedules and event actions are performed on the "Schedule" page by designating a day of the week and time. It is possible to create a time table by dividing a day into up to 6 time zones and to
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 80
    -event Duration] Select the recording duration at an alarm occurrence (postevent recording duration). 2s/5s/10s/20s/30s/1min/3min/5min/10min/15min Manual: Recording duration will be as follows depending on the alarm type. Video motion detection (VMD): Recording will be per- formed for 8 seconds. At
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 81
    Assign a program after setting the time zone [Time table] Select the [Time table] tab on the "Schedule" page. (☞ Page 60) A time table for program actions can be created for each day of the week, and programs can be assigned to each time table. Up to 6 time tables can be created for each day of the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 82
    [Panasonic alarm protocol] Select "On" or "Off" to determine whether or not to automatically notify the PC of the event information by Panasonic alarm protocol at an event occurrence. [Mail] Select "On" or "Off" to determine whether or not to transmit the alarm mail according to the settings of the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 83
    Configure the settings relating to display [Display] The settings relating to the display on Monitor 1 and Monitor 2 connected to the recorder and the display on a PC monitor connected to the recorder via a network can be configured on the "Display" page. The settings relating to display switching
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 84
    Configure the multi screen display pattern and assign camera channels to each multi screen segment Select the display pattern when switching to the multi screen display. In addition, assign the camera channels to each multi screen segment. When selecting the [Setup] button of "Multi screen setup" on
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 85
    Step 2 Select the desired camera channels to display on the multi screen. Select the [Setup] button of "Camera setup". Step 3 Select the desired camera channels to display on each segment on the multi screen. To return to the [Common] tab, select the [Back] button. → The setup page for camera
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 86
    Configure the display settings for Monitor 1 [Monitor 1] Select the [Monitor 1] tab on the "Display" page. (☞ Page 60) Select "On" or "Off" to determine whether or not to display the time, camera title and alarm display on Monitor 1. The settings relating to the sequence display on Monitor 1 can
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 87
    Configuring the sequence display settings Configure the sequential display settings of camera images. When selecting the [Setup] button of "Live sequence" on the [Monitor 1] tab, the setup page for live sequence will be displayed. (☞ Page 86) Configure the following setting items for each step
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 88
    Configure the display settings for Monitor 2 [Monitor 2] Select the [Monitor 2] tab on the "Display" page. (☞ Page 60) Set the position to display the status bar and select "On" or "Off" to determine whether or not to display the camera title. The settings relating to the sequence display on Monitor
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 89
    Configure the camera title [Camera title] Select the [Camera title] tab on the "Display" page. (☞ Page 60) The camera title can be configured on this tab. [Display] Enter a camera title to be displayed on Monitor 2. Enter up to 14 alphanumeric characters for the camera title. Note: • Available
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 90
    Configure the settings relating to the sequential display on a PC monitor [Network] Select the [Network] tab on the "Display" page. (☞ Page 60) The settings for the sequential display when displaying images on a monitor of a PC connected to this recorder via a network can be configured on this tab.
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 91
    [4-screen live sequence] Configure the settings for the sequential display when displaying images with the sequential display on a 4-split screen. When the [Setup] button is selected, the following setup page will be displayed to configure each setting item. • [Cam.] Select a camera image to be
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 92
    Configure the settings relating to communication with other devices [Communication] It is necessary to apply the same settings such as the communication speed and the communication protocol to the recorder and the external devices such as a controller connected to the DATA port on the rear panel of
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 93
    Configure the settings relating to PS·Data [PS·Data setup] Select the [PS·Data setup] tab on the "Communication" page. (☞ Page 60) The settings for PS·Data can be configured on this tab. [Unit address (system)] A unit address is a unique number to be assigned to each PS·Data compatible device.
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 94
    Configure the settings relating to RS485 [RS485 setup] Select the [RS485 setup] tab on the "Communication" page. (☞ Page 60) The settings for RS485 can be configured on this tab. [Protocol] Select the protocol used for RS485 communication. Panasonic/Pelco-D Default: Panasonic [Baud rate]
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 95
    ] Enter the NTP server address when adjusting the time using the NTP server. The name of the NTP server is available only when selecting "Manual" or "Auto" for the "Network" page - the [DNS] tab. Enter up to 255 alphanumeric characters including hyphens (-) and periods (.). Important: • When "On" is
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 96
    address] Enter an address or name of the FTP server to transmit images. The name of the FTP server is available only when selecting "Manual" or "Auto" for the "Network" page - the [DNS] tab. Enter up to 255 alphanumeric characters including hyphens (-) and periods (.). [User name] Enter a user name
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 97
    The settings of alarm mail notice, the settings of error report mail (☞ Operating Instructions (PDF)) and the settings to use the mail functions can be configured on send e-mails. The name of the SMTP server is available only when selecting "Manual" or "Auto" for the "Network" page - the [DNS] tab.
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 98
    [Other destinations] Add other destinations. When the [Setup] button is selected, the following page will be displayed. When the [Setup] button is selected, the following page will be displayed. Enter the desired mail address and mail type for "Address 1" - "Address 4". The setup procedure is the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 99
    . Select "On" to obtain an IP address, a subnet mask and a gateway address from the DHCP server. Set to "Off" when entering the addresses above manually. The IP address, subnet mask and default gateway obtained from the DHCP server are displayed on each setting area. Default: Off Note: • When the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 100
    Maintenance port The setting for the maintenance port behind the front cover of the recorder is configured. This setting is required to maintain and support the recorder from a PC connected via a network using the maintenance port. [IP address] When "Off" is selected for "DHCP", enter an IP address
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 101
    settings relating to DNS (Domain Name System) can be configured on this tab. [DNS] Determine whether or not to use the DNS. Off/Auto/Manual • Select "Manual" or "Auto" to enable IP address searching by the host name using the DNS. • Select "Off" when not using the DNS. • Selecting "Auto" is
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 102
    Configure the settings relating to DDNS [DDNS] Select the [DDNS] tab on the "Network" page. (☞ Page 60) The settings relating to DDNS (Dynamic Domain Name System) can be configured on this tab. [DDNS] Select "On" or "Off" to determine whether or not to use the DDNS. When "On" is selected,
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 103
    Configure the settings relating to SNMP [SNMP] Select the [SNMP] tab on the "Network" page. (☞ Page 60) The settings for the SNMP can be configured on this tab. The settings are configured to check the status of the recorder, etc. by connecting the SNMP manager. [Community] Enter a name used for
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 104
    addresses of the recipient PCs. Enter the IP address or host name for "Address 1" - "Address 8". The host name is available only when selecting "Manual" or "Auto" for the "Network" page - the [DNS] tab. Up to 8 destinations can be registered. Enter up to 255 alphanumeric characters including hyphens
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 105
    Configure the settings relating to network transmission [Transmission] Select the [Transmission] tab on the "Network" page. (☞ Page 60) The settings relating to the resolution and rate to transmit live images to a PC via a network can also be configured on this tab. [Live video resolution]
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 106
    Configure the settings relating to the user management [User mng.] The settings relating to the user authentication On/Off, PSD user, administrator registration and operation levels can be configured on the "User mng." page. It is possible to restrict users and hosts (PCs) to access the recorder by
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 107
    ■ PS.Data [PSD user] Configure the settings for a user when using a PS·Data compatible controller. A PSD user should be one of the registered users for the recorder. An auto login user should be one of the users registered in the recorder. Register or change the administrator information [
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 108
    Register, change or delete the user information [User] Select the [User] tab on the "User mng." page. (☞ Page 60) The user information such as the user name, password and operation level can be registered, changed and deleted on this tab. Registers user information Register user information such as
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 109
    Change or delete the user information Change or delete the user information that has been registered. Step 1 Select the [Edit/delete] button on the [User] tab. Step 3 To change the user information, select the [Edit] button after changing the user information by performing the same procedure as
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 110
    Register, change, or delete a PC (host) accessible to this recorder [Host] Select the [Host] tab on the "User mng." page. (☞ Page 60) The information of host that accesses the recorder via a network can be registered, changed and deleted on this tab. Registers host information Registers the host
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 111
    Change or delete the host information Change or delete the host information that has been registered. Step 1 Select the [Edit/delete] button on the [Host] tab. Step 3 To change the host information, select the [Edit] button after changing the host information by performing the same procedure as
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 112
    action can be canceled. (☞ Operating Instructions (PDF)) An error action can be canceled. (☞ Operating Instructions (PDF)) An alarm action can be suspended. (☞ Operating Instructions (PDF)) A recorded image can be manually copied. (☞ Operating Instructions (PDF)) Manual recording can be started and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 113
    depth, it is also possible to designate the size of an object and the motion range of a person or an object. Refer to the operating instructions of SD5 cameras for further information about the i-VMD function. Refer to the "readme.txt" on the provided CD-ROM about the dedicated software. 113
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 114
    Setting the detection areas and sensitivity Step 1 Select the [Setup] button of the [i-VMD setup] tab. Step 3 Select the [Area/Sensitivity] tab. → The [Area/Sensitivity] tab will be displayed. → The setup page for camera's i-VMD function will be displayed. Note: • When no operation is made for
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 115
    Step 5 Set the start point of the detection area. Move the cursor to the desired start point, and click the mouse button. Note: • To delete a set detection area, select the [Area delete] tab on the setup page for camera's i-VMD function, and click the [Delete] button of the area (White/Blue/Green/
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 116
    Setting the scene change Select "On" or "Off " to determine whether to provide an alarm signal when a change in the state of scene occurs by covering the camera with a cloth, a cap, or others, or by changing the camera direction largely. Setting the detection mode Set the detection conditions for "
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 117
    Setting the detection depth Set the detection depth of the detected areas. By setting the detection depth, it is possible to automatically calculate the size of object to be detected on the screen to reduce the detection failure. To calculate the detection depth properly, mount the camera
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 118
    Uploading or downloading the settings of SD5Link cameras [Setup data] Select the [Setup data] tab on the "SD5Link" page. (☞ Page 60) It is possible to retrieve setup data of an SD5Link camera and to load the retrieved data to the SD5Link camera. [Setup data] The setup data downloaded from
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 119
    Configure the settings relating to maintenance [Maintenance] The version of the recorder and disk information is displayed, and the settings relating to hard disk drives can be configured on the "Maintenance" page. It is also possible to initialize the setup data of the setup pages, format SD memory
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 120
    areas and operation modes (single mode/RAID5 mode/RAID6 mode) of hard disk drives. • [NML rec.] Displays the total capacity of manual recording areas and schedule recording areas. • [EVT rec.] Displays the total capacity of emergency recording areas and post-event recording areas. • [Pre
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 121
    [Pre-recording area information] When the [Display] button is selected, the "Pre-recording area info." page will be displayed, and the capacity of the pre-event recording area assigned to each camera channel. When the [Back] button is selected, the "Pre-recording area information" page will be
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 122
    h/40 000 h/50 000 h Default: 20 000h 122 ■ Data delete Deletes the data from the hard disk drives. The two ways to delete data are auto deletion and manual deletion by designating the date. • [HDD auto delete] Configure the settings to delete data automatically when the set days have passed
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 123
    Manage the settings [Settings management] Select the [Settings management] tab of the "Maintenance" page. (☞ Page 60) The settings of the setup pages can be saved in the SD memory card, and saved settings can be called up (loaded) from the recorder on this tab. It is also possible to restore the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 124
    View Log Information [Logs] Select the [Logs] tab of the "Maintenance" page. (☞ Page 60) The following logs can be checked on this tab. Error log: Logs of error Access log: Logs of accessing the recorder Event log: Logs of event occurrence time & date and details Network log: Check the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 125
    Check the network error log The network error logs (occurrence time & date and error details) will be displayed in list form. Refer to the Operating Instructions (PDF) for further information about the events. When the [Network log] button of the [Logs] tab is selected, the following page will be
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 126
    when an event does not occur (Manual recording, schedule recording) • Event regarded logically as a single drive. Even if a trouble occurs in one of the hard disk drives, the recorder. (☞ Page 20) • Refer to the operating instructions of extension units for further information about how to determine
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 127
    About the disk configuration page The operations relating to the hard disk drives such as checking the capacity of each recording area and formatting the drives can be performed on the disk configuration page. Important: • All other operations such as recording and playback will stop when the disk
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 128
    Check the hard disk drive information The original capacity, the available capacities of the hard disk drives of the recorder or the extension units (Ext.1 to 3), and capacities of each recording area will be displayed. Select the [Disk Information] tab of the "Disk Information" page on the disk
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 129
    Format the hard disk drives [Format] Hard disk drives will be formatted, and one of the normal recording area, event recording area or pre-event recording area will be assigned to each drive. It is necessary to format a hard disk drive on either of the following conditions. • When an hard disk drive
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 130
    Step 4 Select the [OK] button. → The format starts, and the message will be displayed to show the drive is being formatted. When formatting is complete, the result of format will be displayed. Step 5 To return to the [Format] tab, select the [Close] button. 130
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 131
    Format the pre-event recording area Configure the following settings relating to the pre-event recording area. • Assign the capacity of pre-event recording area to each camera channels. • Format a hard disk drive set for another recording area again to set for the pre-event recording area. • Format
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 132
    Step 4 Select the hard disk drive on which the pre-event recording area is to be created (or added) and select the [Set] button. Step 5 Select the desired camera channel for the selected hard disk drive, and enter the capacity to be assigned. • Pre-event recording areas for up to 16 camera channels
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 133
    52) Note: • When replacing the hard disk units from the extension unit, take the same procedures as replacement of the recorder's. Refer to the operating instructions of the extension unit for how to install the hard disk units on the extension unit. • Refer to page 146 for how to replace a faulty
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 134
    Step 3 Select the hard disk drive to be shut down, and select the [OK] button. When the hard disk drive on the recorder is to be shut down: Main-y ("y" indicates the hard disk drive number.) When the hard disk drive on the extension unit is to be added to the system: Ext.x-y ("x" indicates
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 135
    Add a hard disk drive Hard disk drives will be locally procured. When adding an HDD unit, proceed as follows. It is possible to add an HDD unit without stopping operation. Install an HDD unit in the recorder (☞ Page 52) ➜ Hard disk drive auto recognition (☞ Page 136) ➜➜ When a hard disk drive is
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 136
    Auto recognition of hard disk drives When installing an HDD unit while the power of the recorder is on, the hard disk drive recognition process will automatically start. During the hard disk drive recognition process, the HDD indicator (STS (status)) on the front panel will blink orange. When an
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 137
    Add a hard disk drive to the system To use the recognized playback-only disk as a recordable disk, it is necessary to add it to the system. Addition the playback-only disk to the system can be made on the HDD Configuration menu. Before the following procedure, detach the front cover from the
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 138
    Operation of the extension unit When connecting an extension unit, it is necessary to add the extension unit to the system. It is also necessary to start the shutdown process of the extension unit to remove the extension unit from the system. Add an extension unit to the system The extension unit
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 139
    Shutdown process of the extension unit It is also necessary to start the shutdown process of the extension unit to remove the extension unit from the system. It is possible to shut down all the hard disk drives in the extension unit by operating as follows. The shutdown process can be started from
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 140
    About the error log The following are the descriptions about the contents of the error log and the network log. • "x" indicates the extension unit number. • "y" indicates the HDD unit number. Content Error log Network Log Outage detection POWER LOSS - Recover from a power out- POWER
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 141
    Content Error log Network Log Single mode format failure RAID5 format failure RAID6 format failure RAID5 1 down RAID5 2 down RAID6 1 down RAID6 2 down RAID6 3 down HDD smart warning HDD hour meter warning HDD SKIP warning Remove auto links (per HDD) Remove auto links (per recorder or extension
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 142
    Content Error log Network Log Partition error (per HDD) Recorder: MAIN-y PARTITION - ERROR Extension unit: EXTx-y PARTITION ERROR Partition error (per unit) Recorder: MAIN PARTITION - ERROR Extension unit: EXTx PARTITION ERROR HDD RAID5 recovery fail- Recorder: MAIN RAID5 - ure
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 143
    Content Error log FTP server transfer com- - plete Failed to resolve FTP serv- - er address from DNS Failed to find FTP server - FTP uploading error - FTP passive mode error - FTP log-in failure - Other error for FTP - DDNS IP address update - Failed to find DDNS server - Password error
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 144
    Content Error log HTTP download failure - HTTP request invalid - Other errors for HTTP - Network Log Display on Monitor 2 DOWNLOAD_ - ERR REQUEST_ERR - OTHER_ERR - Output from the connector at the rear panel - - - 144
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 145
    even when 2 hard disk drives become faulty (2 down). When the hard disk drive becomes faulty (down), replace it immediately. Refer to the operating instructions of the extension unit. * Contact your dealer about replacement of HDD units. Important: • In the RAID 5 mode: If 2 or more hard disk
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 146
    Replacement of a faulty hard disk drive in the RAID mode In the RAID 5 mode, it is possible to read data on the other hard disk drives and recover data even when a single hard disk drive becomes faulty (1 down). In the RAID 6 mode, it is possible to read data on the other hard disk drives and
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 147
    Troubleshooting Check the following before requesting repair. Contact a dealer if a problem cannot be solved even after checking and trying the solution or if a problem is not described below, or when having a problem with installations. Symptom Check item/Remedy Ref. Page Power is not turned
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 148
    it. • Depending on the photographic subject or HDMI monitor that is connected, images or embedded characters may look blur- - ry. That is not a trouble. • Have images certainly been recorded? Check if there are recorded images on the recorder. 119 • Is the user level of the current login
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 149
    on the operation panel? When the "BUSY" indication is displayed on the operation panel, a user with higher priority is controlling the camera. Operating Instructions (PDF) • Are signals correctly supplied to the ALARM/CONTROL connector and the ALARM connector at the rear? • Is the ALARM connector
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 150
    devices to the same UPS. - • Make sure that the HDD unit is inserted all the way into the HDD slot. 52 • The hard disk drive is faulty. - • Add the subsequent faulty disks. • Make sure that the HDD unit is inserted all the way into the 52 HDD slot. • The hard disk drive on which there is
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 151
    . Check item/Remedy Ref. Page • Are the network settings of the recorder and the PC configured correctly? Check the settings. Operating Instructions (PDF) • Is the host registration configured correctly? When "On" is selected for "Host authentication", it is impossible to access the recorder
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 152
    . If updating the driver does not solve the problem, adjust the hardware acceleration as follows. The following click the [Advanced] button. 3. Click the [Troubleshoot] tab and disable the DirectDraw acceleration by adjusting service personnel. Ref. Page - The power cord gets hot when bent or stretched
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 153
    8 to 16ch alarm output*3, alarm reset input*2, emergency recording input*2, available space warning output*3, HDD trouble output*3, camera trouble output*3, trouble out- put*3, electricity failure recovery completion output*4, time adjust input/output*5, sequence switching input/output*5, alarm
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 154
    1 Standard accessories CD-ROM*1 1 pc. Installation Guide (this document 1 pc. Quick Reference Guide 1 pc. Warranty 1 pc. The following are 24 pcs. *1 The CD-ROM contains the operating instructions (PDFs) and other manuals. Optional Accessories Built-In DVD WJ-HDB611 RAID Board
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 155
    155
  • Panasonic WJ-HD616/1000 | Installation Guide - Page 156
    Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way 2H-2, Secaucus, New Jersey 07094 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
No model number suffix is shown in this manual.
Installation Guide
Digital Disk Recorder
Model No.
WJ-HD616K
WJ-HD716K
ERROR
ALARM
ALARM
SUSPEND
STS
HDD1
A/F
TIMER
HDD2
HDD3
OPERATE
HDD4
ALARM
RESET
GOTO LAST
GOTO DATE
SEARCH
COPY
REV
FWD
SETUP
SET
HOLD
SUB
MENU
ESC
STOP
PAUSE
PLAY
REC
REC STOP
MOUSE
Digital Disk Recorder WJ-HD616
3
2
7
6
12
11
16
15
MONITOR
SEQ
MULTI SCREEN
OSD
1
5
9
4
8
0/10
14
13
This illustration represents WJ-HD616K.