Pfaff coverstyle 4850 Owner's Manual - Page 15

Presserfoot, Changing the presser foot, Turn off the electrical power, To remove, To attach, Check

Get Pfaff coverstyle 4850 PDF manuals and user guides View all Pfaff coverstyle 4850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Presserfoot With standard presser foot 10 use setting "A" on the spring loaded presser foot latch for the cover stitch (Prog. 02), the 2 thread chainstitch (Prog. 01), the 5 thread safety stitch seam (Prog. 09) and the 4 thread safety stitch seam (Prog. 08). Transparent presser foot F from the accessories can also be used for the cover stitch (Prog. 02). For all other programs use standard presser foot 10 and setting "B" on the springloaded presser foot latch. Changing the presser foot Turn off the electrical power To remove: Raise the needle(s) to the highest position by turning the hand wheel towards you. Raise the presser foot and press lever A at the rear of the presser foot holder. The presser foot will be released automatically from the holder. Pivot the presser foot clockwise until the front half of presser foot clears holder and remove by sliding foot away from you towards back of machine. To attach: Place the presser foot behind and perpendicular to the presser foot holder. Pivot the presser foot counterclockwise until the pin of the foot is directly under the presser foot holder clamp. Lower the presser foot lever and press lever A, if necessary, until the foot then clicks into place. Check: Please lift the presser foot lever to ensure that the presser foot is properly locked into place. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
11
Presserfoot
With standard presser foot
10
use setting
”A”
on the spring loaded presser foot latch for the
cover stitch (Prog. 02), the 2 thread chainstitch
(Prog. 01), the 5 thread safety stitch seam
(Prog. 09) and the 4 thread safety stitch seam
(Prog. 08).
Transparent presser foot
F
from the accessories
can also be used for the cover stitch (Prog. 02).
For all other programs use standard presser
foot
10
and setting
”B”
on the springloaded
presser foot latch.
Changing the presser foot
Turn off the electrical power
To remove:
Raise the needle(s) to the highest
position by turning the hand wheel towards
you. Raise the presser foot and press lever A at
the rear of the presser foot holder. The presser
foot will be released automatically from the
holder. Pivot the presser foot clockwise until
the front half of presser foot clears holder and
remove by sliding foot away from you towards
back of machine.
To attach:
Place the presser foot behind and
perpendicular to the presser foot holder. Pivot
the presser foot counterclockwise until the pin
of the foot is directly under the presser foot
holder clamp. Lower the presser foot lever and
press lever
A
, if necessary, until the foot then
clicks into place.
Check:
Please lift the presser foot lever to
ensure that the presser foot is properly locked
into place.