Philips AZ1012 User manual - Page 15

Troubleshooting

Get Philips AZ1012 PDF manuals and user guides View all Philips AZ1012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair. Do not open the set as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Problem No sound Power cord not securely connected Batteries dead /incorrectly inserted Display does not function properly/ No reaction to operation of any of the controls Er indication CD badly scratched or dirty Laser lens steamed up CD-(R) is blank or the disc is not finalized CD playback does not work The CD skips tracks Poor cassette sound quality Recording does not work Solution - Adjust the VOLUME - Connect AC power cord properly - Insert (fresh) batteries correctly - Electrostatic discharge - Switch off and unplug the set. Reconnect after a few seconds. - No CD inserted, insert a CD - Replace/ clean CD, see Maintenance - Wait until lens has cleared - Wait until lens has acclimatized - Use a finalized CD-(R) - CD badly scratched/ dirty. Replace/ clean CD (see maintenance) - CD damaged or dirty. Replace or clean CD. - Program is active. Quit program mode - Dust and dirt on the heads, etc. Clean deck parts, see maintenance. - Use of incompatible cassette types (METAL or CHROME). Only use NORMAL (IEC I) for recording - Cassette tab(s) may be broken. Apply a piece of adhesive tape over the missing tab space. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
If a fault occurs, first check the points listed below
before taking the set for repair. Do not open the
set as there is a risk of electric shock.
If you are unable to remedy a problem by following
these hints, consult your dealer or service center.
WARNING: Under no circumstances should you try
to repair the set yourself, as this will invalidate the
warranty.
Troubleshooting
15
English
Problem
Solution
No sound
– Adjust the VOLUME
Power cord not securely
– Connect AC power cord properly
connected
Batteries dead /incorrectly
– Insert (fresh) batteries correctly
inserted
Display does not function
– Electrostatic discharge
properly/ No reaction to
– Switch off and unplug the set. Reconnect after a few
operation of any of the
seconds.
controls
Er
indication
– No CD inserted,insert a CD
CD badly scratched or dirty
– Replace/ clean CD, see Maintenance
Laser lens steamed up
– Wait until lens has cleared
– Wait until lens has acclimatized
CD-(R) is blank or the disc
– Use a finalized CD-(R)
is not
fi
nalized
CD playback does not work
– CD badly scratched/ dirty. Replace/ clean CD (see
maintenance)
The CD skips tracks
– CD damaged or dirty. Replace or clean CD.
– Program is active. Quit program mode
Poor cassette sound quality
– Dust and dirt on the heads,etc.
Clean deck parts, see maintenance.
– Use of incompatible cassette types (METAL or
CHROME). Only use NORMAL (IEC I) for recording
Recording does not work
– Cassette tab(s) may be broken.Apply a piece of
adhesive tape over the missing tab space.