Pioneer P7600DVD Owner's Manual - Page 82

Audio Adjustments

Get Pioneer P7600DVD - DVD Player With LCD Monitor PDF manuals and user guides
UPC - 012562745602
View all Pioneer P7600DVD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Section 15 Audio Adjustments ! Auto TA and EQ changes the audio settings as below:  The fader/balance settings return to the center position. (Refer to page 76.)  The equalizer curve switches to FLAT. (Refer to page 74.)  It will be adjusted automatically to high pass filter setting for front, center and rear speaker. ! If you carry out auto TA and EQ when a previous setting of this already exists, the setting will be replaced. Carrying out auto TA and EQ 1 Stop the car in a place that is as quiet as possible, close all doors, windows and the sun roof, and then turn the engine off. If the engine is left running, engine noise may prevent correct auto TA and EQ. 2 Fix the supplied microphone in the center of the headrest of the drivers seat, facing forward, using the belt (sold separately). The auto TA and EQ may differ depending on where you place the microphone. If desired, place the microphone on the front passenger seat to carry out auto TA and EQ. conditioner or heater may prevent correct auto TA and EQ. # Press SOURCE to turn the source on if this unit is turned off. 4 Select the position for the seat on which the microphone is placed. Refer to Using the position selector on page 76. # If no position is selected before you start auto TA and EQ, FL is selected automatically. 5 Press SOURCE and hold until the unit turns off. 6 Press and hold EQ to enter the auto TA and EQ measurement mode. 7 Plug the microphone into the microphone input jack on the hide-away unit. 3 Turn the ignition switch to ON or ACC. If the cars air conditioner or heater is turned on, turn it off. Noise from the fan in the air 8 Touch START to start the auto TA and EQ. 9 Get out of the car and close the door within 10 seconds when the 10-second count-down starts. The measurement tone (noise) is outputted from the speakers, and auto TA and EQ begins. # When all speakers are connected, auto TA and EQ is completed in about nine minutes. # To stop auto TA and EQ, touch STOP. 82 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
!
Auto TA and EQ changes the audio settings
as below:
µ
The fader/balance settings return to the
center position. (Refer to page 76.)
µ
The equalizer curve switches to
FLAT
.
(Refer to page 74.)
µ
It will be adjusted automatically to high
pass filter setting for front, center and
rear speaker.
!
If you carry out auto TA and EQ when a pre-
vious setting of this already exists, the set-
ting will be replaced.
Carrying out auto TA and EQ
1
Stop the car in a place that is as quiet
as possible, close all doors, windows and
the sun roof, and then turn the engine off.
If the engine is left running, engine noise may
prevent correct auto TA and EQ.
2
Fix the supplied microphone in the cen-
ter of the headrest of the driver
³
s seat, fa-
cing forward, using the belt (sold
separately).
The auto TA and EQ may differ depending on
where you place the microphone. If desired,
place the microphone on the front passenger
seat to carry out auto TA and EQ.
3
Turn the ignition switch to ON or ACC.
If the car
±
s air conditioner or heater is turned
on, turn it off. Noise from the fan in the air
conditioner or heater may prevent correct auto
TA and EQ.
#
Press
SOURCE
to turn the source on if this
unit is turned off.
4
Select the position for the seat on
which the microphone is placed.
Refer to
Using the position selector
on page
76.
#
If no position is selected before you start auto
TA and EQ,
FL
is selected automatically.
5
Press SOURCE and hold until the unit
turns off.
6
Press and hold EQ to enter the auto TA
and EQ measurement mode.
7
Plug the microphone into the micro-
phone input jack on the hide-away unit.
8
Touch START to start the auto TA and
EQ.
9
Get out of the car and close the door
within 10 seconds when the 10-second
count-down starts.
The measurement tone (noise) is outputted
from the speakers, and auto TA and EQ be-
gins.
#
When all speakers are connected, auto TA
and EQ is completed in about nine minutes.
#
To stop auto TA and EQ, touch
STOP
.
Audio Adjustments
En
82
Section
15