ProForm 14.0 Ce Elliptical English Manual - Page 8

Tip: Avoid pinching the Wire Harness 60.

Get ProForm 14.0 Ce Elliptical PDF manuals and user guides View all ProForm 14.0 Ce Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Tip: Avoid pinching the Wire Harness (60). Insert the Upright (5) into the Main Frame (1). Attach the Upright (5) with four M8 x 16mm Screws (102) and four M8 Split Washers (103); do not tighten the Screws yet. 4 Avoid pinching the Wire Harness (60) 60 102 103 5 102 103 1 102 103 102 5. Using a small plastic bag to keep your fingers clean, apply a coat of the included grease to the Upright Axle (48) and to two Wave Washers (118). Tip: Avoid damaging the Wire Harness (60). Insert the Upright Axle (48) through the Upright (5) and center it. Slide a Wave Washer (118) onto each side of the Upright Axle. Next, identify the Right and Left Upper Body Legs (6, 7), which are marked with “"Right”" and “"Left”" stickers, and orient them as shown. Slide the Right and Left Upper Body Legs (6, 7) onto the right and left sides of the Upright Axle (48). Tighten an M8 x 16mm Screw (102) and an M8 Washer (95) into each end of the Upright Axle (48) at the same time. 5 102 95 7 60 Avoid damaging the 118 Wire Harness (60) 5 Grease 48 Grease 118 102 95 6 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
8
4.
Tip: Avoid pinching the Wire Harness (60).
Insert the Upright (5) into the Main Frame (1).
Attach the Upright (5) with four M8 x 16mm
Screws (102) and four M8 Split Washers (103);
do not tighten the Screws yet.
4
5
102
102
102
102
103
103
103
1
Avoid pinching the
Wire Harness (60)
5
5.
Using a small plastic bag to keep your
fingers clean, apply a coat of the included
grease to the Upright Axle (48) and to two Wave
Washers (118).
Tip: Avoid damaging the Wire Harness (60).
Insert the Upright Axle (48) through the Upright
(5) and center it. Slide a Wave Washer (118)
onto each side of the Upright Axle.
Next, identify the Right and Left Upper Body
Legs (6, 7), which are marked with ²Right³ and
²Left³ stickers, and orient them as shown.
Slide the Right and Left Upper Body Legs
(6, 7) onto the right and left sides of the Upright
Axle (48).
Tighten an M8 x 16mm Screw (102) and an M8
Washer (95) into each end of the Upright Axle
(48) at the same time.
Avoid damaging the
Wire Harness (60)
Grease
Grease
95
5
7
102
95
102
118
48
60
6
118
60