RCA RCR412S Owner/User Manual: RCR412S - Page 3

RCR412S_NA_IB_REVA.qxd 5/21/04 1:03 PM Page 4 Programming the Remote Your universal remote can operate a variety of brands of components. In order for your universal remote to control your components, you need to program the remote with the codes that match the components (See Code Lists enclosed). These codes enable the remote to communicate with your components. Each brand and each component has its own "language," and, by programming the correct codes into your remote, you tell the remote to "speak the same language" as your components. There are four methods you can use to program your remote control to operate your components: Brand Code Search and Entry, Direct Code Entry, Manual Code Search and Entry, and Auto Code Search and Entry. Most components can be programmed in one of these four ways. Try them in the order listed. In order to control combo units, like TV/VCRs, TV/DVDs or TV/VCR/DVDs, you must program the individual corresponding component keys to control each part of the combo unit. Once programmed successfully, the TV key controls the TV functions on your unit, and the DVD or VCR·AUX key controls the DVD or VCR functions, respectively. There is a specific section in the Code Lists for combo units. The codes in this section should be tried first, using Direct Code Entry on the TV and DVD or VCR·AUX keys. If this is unsuccessful, follow the normal programming methods for both the TV and the DVD or VCR·AUX keys. VCR·AUX KEY Important: The VCR·AUX key defaults to program a VCR. If you want the VCR·AUX key to control a component other than a VCR (an additional TV or DVD, for example), it is necessary for you to preprogram the VCR·AUX key. See the section entitled "Programming the VCR·AUX Key To Control a Component Other Than a VCR" on page 6. Programming Methods Brand Code Search and Entry If your brand is listed in the Brand Code List (See Code Lists enclosed), you may be able to program your universal remote by searching through only the Code Lists for that specific manufacturer. Brand Code Search and Entry can be the quickest method to program your remote, if your component (TV, DVD, VCR and satellite receiver or cable box) is one of those brands listed. If your brand is not listed in the Brand Code List, use one of the other programming methods that follow. Follow these instructions to program your remote using the Brand Code Search and Entry method. GO BACK ! TIP: To exit without saving at any point in the Brand Code Search, press and release the GO BACK key. 1. Manually turn on the component you want the remote to control (TV, VCR, DVD, satellite receiver or cable box). 2. Locate the Brand Codes in the Code Lists and keep it handy. Note: If you press an invalid key during the Brand Code Search, the remote does not respond. If you do not press a valid Brand Code Search key (TV, DVD, VCR·AUX, SAT·CBL, ON·OFF, GO BACK, and number keys 0-9), the search times out after two minutes. When the search times out, the illuminated ON·OFF key blinks four times and turns off. The last programmed code under that component key is retained. SAT·CBL TV VCR·AUX ON·OFF 4 3. Press and hold the component key (TV, DVD DVD, VCR·AUX, SAT·CBL) you wish to program. (To program the VCR·AUX key to control a component other than a VCR, see page 6). The illuminated ON·OFF key turns on and remains on. 4. While holding the component key down, press and hold the ON·OFF key. The illuminated ON·OFF key turns off. ON·OFF (ON) ON·OFF (BLINK) ON·OFF (BLINK) STOP ON·OFF (OFF) 5. After holding both keys down for three seconds, the illuminated ON·OFF key turns back on. 6. Release both keys. The illuminated ON·OFF key remains on. 7. Refer to the Brand Codes in the enclosed Code Lists. Press and release the appropriate brand code key (Numbers 0-9), using the number keys on the keypad. The illuminated ON·OFF key blinks once. ! TIP: Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control. 8. Press and release the ON·OFF key repeatedly until your component turns off. Each time you press the ON·OFF key, the illuminated ON·OFF key blinks, and the next code is sent. The Brand Code Search begins with the first code in the chosen brand list for that component and cycles through all the codes for that brand. If your component turns off, you have found the correct code. (If it cycles through and the illuminated ON·OFF key blinks four times and turns off, all codes in the chosen brand lists have been searched and another programming method should be tried. The Brand Code Search mode is exited.) 9. Once you have found the correct code, you must save that code by pressing and releasing the STOP key. The illuminated ON·OFF key turns off. You must press the STOP key to save the code or the correct code will not be stored! 10. To confirm that the component key is programmed with the correct code for maximum functionality, test the component. Attempt to control a variety of the component's functions with the remote. If some of the features of your component do not work, try programming the remote with a different programming method. Direct Code Entry To program your universal remote to control your components using the Direct Code Entry Method, follow the steps below. SAT·CBL TV VCR·AUX DVD ON·OFF (ON) ON·OFF (BLINK) 1. Manually turn on the component you want the remote to control (TV, VCR, DVD, satellite receiver or cable box). 2. Locate the enclosed Code Lists. Find the list for the component you wish to program. Find your component's brand. You will see a listing of four-digit codes for each brand. If your brand isn't listed, use one of the Code Search methods to program the remote control. (Refer to pages 7-8 for Manual and Auto Code Search methods.) 3. Press and hold the component key (TV, DVD, VCR·AUX, SAT·CBL) you wish to program. (To program the VCR·AUX key to control a component other than a VCR, see page 7.) The illuminated ON·OFF key turns on and remains on. If you release the component key any time during the Direct Code Entry procedure, the illuminated ON·OFF key blinks four times, and the process is exited. The last programmed code under the component key is retained. 5