Ricoh Priport DX 4640PD Printer Reference - Page 83

 Troubleshooting, Error & Status Messages on the Display Panel

Get Ricoh Priport DX 4640PD PDF manuals and user guides View all Ricoh Priport DX 4640PD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

5. Troubleshooting Error & Status Messages on the Display Panel Messages/Second messages Descriptions and Solutions Ethernet board Error. An error has occurred in the Ethernet module. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. Wireless card error. IEEE 802.11b card was not inserted when the printer was turned on, or it was pulled out after the printer turned on. Turn off the printer and check the IEEE 802.11b card is inserted correctly. Then, turn the printer on again. If the message appears again, contact your sales or service representative. Wireless board error. An error has occurred in the IEEE 802.11b module. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. Master Processing... The master is being made. Memory switch error. An error has occurred in the memory unit. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. Optional RAM error. An error has occurred in the SDRAM module. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. Printing... Data is being printed. Wait until the job is finished. Parallel I/F board error. An error has occurred in the parallel I/F board. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. DIMM value error. An error has occurred in the PostScript3 bored. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. HDD board error. An error has occurred in the HDD board. Turn off the main power switch, and back on again. If the message appears again, contact your sales or service representative. Print is not finished. Printing is not finished. Printing has been interrupted. Perform one of the following procedures: • Press the {Start} key, and printing will restart. Before the print amount display reaches 0, press the {Start} key to print. • Press [End Printing] , and printing will stop. The interrupted prints will not be performed. Ready Master Making or print data is on the spool. This is not an error. Press the {Start} key to begin master making or printing. 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
77
5. Troubleshooting
Error & Status Messages on the Display Panel
Messages/Second messages
Descriptions and Solutions
Ethernet board Error.
An error has occurred in the Ethernet module.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
Wireless card error.
IEEE 802.11b card was not inserted when the printer was turned
on, or it was pulled out after the printer turned on.
Turn off the printer and check the IEEE 802.11b card is inserted
correctly. Then, turn the printer on again. If the message ap-
pears again, contact your sales or service representative.
Wireless board error.
An error has occurred in the IEEE 802.11b module.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
Master Processing...
The master is being made.
Memory switch error.
An error has occurred in the memory unit.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
Optional RAM error.
An error has occurred in the SDRAM module.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
Printing...
Data is being printed.
Wait until the job is finished.
Parallel I/F board error.
An error has occurred in the parallel I/F board.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
DIMM value error.
An error has occurred in the PostScript3 bored.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
HDD board error.
An error has occurred in the HDD board.
Turn off the main power switch, and back on again. If the mes-
sage appears again, contact your sales or service representative.
Print is not finished.
Printing is not finished.
Printing has been interrupted. Perform one of the following
procedures:
•
Press the
{
Start
}
key, and printing will restart. Before the
print amount display reaches 0, press the
{
Start
}
key to print.
•
Press
[
End Printing
]
, and printing will stop. The interrupted
prints will not be performed.
Ready<Online>
Master Making or print data is on the spool. This is not an error.
Press the
{
Start
}
key to begin master making or printing.