Ryobi P552 Manual 1 - Page 26

Cutting Warped Material, Warning

Get Ryobi P552 PDF manuals and user guides View all Ryobi P552 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

OPERATION Bevel Angle Setting 33.85° 33.85° 33.85° 33.85° Type of Cut Left side, inside corner 1. Top edge of molding against fence 2. Miter table set right 31.62° 3. Save left end of cut Right side, inside corner 1. Bottom edge of molding against fence 2. Miter table set left 31.62° 3. Save left end of cut Left side, outside corner 1. Bottom edge of molding against fence 2. Miter table set left 31.62° 3. Save right end of cut Right side, outside corner 1. Top edge of molding against fence 2. Miter table set right 31.62° 3. Save right end of cut CUTTING WARPED MATERIAL See Figures 32 - 33. When cutting warped material, always make sure it is positioned on the miter table with the convex side against the fence as shown in figure 32. If the warped material is positioned the wrong way as shown in figure 33, it will pinch the blade near the completion of the cut. WARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence. 45 31.6 30 22.5 22.5 30 31.6 15 0 15 RIGHT 45 31.6 30 22.5 22.5 30 31.6 15 0 15 WRONG 45 45 Fig. 32 Fig. 33 26 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
26 – English
OPERATION
Bevel
Angle
Type of Cut
Setting
Left side, inside corner
1. Top edge of molding against fence
2. Miter table set right 31.62°
3. Save left end of cut
Right side, inside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62°
3. Save left end of cut
Left side, outside corner
1. Bottom edge of molding against fence
2. Miter table set left 31.62°
3. Save right end of cut
Right side, outside corner
1. Top edge of molding against fence
2. Miter table set right 31.62°
3. Save right end of cut
33.85°
33.85°
33.85°
33.85°
CUTTING WARPED MATERIAL
See Figures 32 - 33.
When cutting warped material, always make sure it is posi-
tioned on the miter table with the convex side against the
fence as shown in figure 32.
If the warped material is positioned the wrong way as shown
in figure 33, it will pinch the blade near the completion of
the cut.
WARNING:
To avoid a kickback and to avoid serious personal injury,
never position the concave edge of bowed or warped
material against the fence.
Fig. 32
RIGHT
WRONG
Fig. 33
45
30
31.6
22.5
15
0
15
30
22.5
31.6
45
45
30
31.6
22.5
15
0
15
30
22.5
31.6
45