Samsung NE58F9500SS/AA User Manual Ver.1.0 (English, French) - Page 25

Step 4. Installing The Conduit - model

Get Samsung NE58F9500SS/AA PDF manuals and user guides View all Samsung NE58F9500SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

STEP 4. INSTALLING THE CONDUIT Remove the conduit connection plate and rotate it as shown below. The conduit hole (11/8") must be used. 11/8" 13/8" CONNECTING THE POWER 13/8" 1. Prepare the conduit cord as shown in Figure 1. 2. Install the conduit cord as shown in Figure 2. Figure 1 1" 3/8" 1" 3/8" 31/2" 3 wire 31/2" 4 wire Knockout surface Conduit connection plate 11/8" Figure 2 Ring Body Strain relief For conduit installations, insert the strain relief (not included) into the conduit hole (11/8"). Then thread the conduit cord through the body of the strain relief and fasten the ring. Reinstall the bracket. Installing a 3-wire conduit • Aluminum building wire may be used but it must be rated for the correct amperage and voltage. Connect the wires as described below. • The wire you use, the location and enclosure of splices, etc., must conform to good wiring practices and local codes. 1. Loosen the 3 lower terminal screws from the terminal block. 2. Insert the center bare wire (white/neutral) tip through the bottom center terminal block opening. On certain models, the wire will need to be inserted through the ground strap opening and then into the bottom center block opening. 3. Insert the two side bare wire tips into the lower left and the lower right terminal block openings. 4. Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs.). Do not over-tighten the screws since it could damage the wires. 5. Go to step 5 on page 25 to continue with the installation. Neutral terminal Black Ground strap White Red Black White Red Wire tips connecting the power _24 130513 (IB_Better)NE58F9500SS_DG68-00499A_EN.indd 24 13/05/2013 08:36:23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
CONNECTING THE POWER
connecting the power _
24
STEP 4. INSTALLING THE CONDUIT
Remove the conduit connection plate and rotate it as shown below.
The conduit hole (1
1
/
8
”) must be used.
1
1
/
8
”
1
3
/
8
”
1
1
/
8
”
1
3
/
8
”
1
.
Prepare the conduit cord as shown in Figure 1.
2
.
Install the conduit cord as shown in Figure 2.
Conduit connection plate
Strain relief
Ring
Body
Figure 2
1”
3
1
/
2
”
3
/
8
”
1”
3
1
/
2
”
3 wire
4 wire
Knockout surface
Figure 1
3
/
8
”
For conduit installations, insert the strain relief (not included) into the conduit hole (1
1
/
8
”). Then thread
the conduit cord through the body of the strain relief and fasten the ring. Reinstall the bracket.
Installing a 3-wire conduit
• Aluminum building wire may be used but it must be rated for the correct amperage and voltage.
Connect the wires as described below.
• The wire you use, the location and enclosure of splices, etc., must conform to good wiring
practices and local codes.
1
. Loosen the 3 lower terminal screws from the
terminal block.
2
. Insert the center bare wire (white/neutral) tip
through the bottom center terminal block opening.
On certain models, the wire will need to be
inserted through the ground strap opening and
then into the bottom center block opening.
3
.
Insert the two side bare wire tips into the lower left
and the lower right terminal block openings.
4
.
Tighten the screws until the wire is firmly secured
(35 to 50 inch-lbs.). Do not over-tighten the
screws since it could damage the wires.
5
. Go to
step 5
on page 25 to continue with the
installation.
White
Black
Red
Ground
strap
Neutral
terminal
Wire tips
Red
White
Black
130513 (IB_Better)NE58F9500SS_DG68-00499A_EN.indd
24
13/05/2013
08:36:23