Samsung RFG298HDRS User Manual (user Manual) (ver.0.2) (English, French, Spani - Page 9

Adjusting The Freezer Drawer, Level, Installing The Water, Dispenser Line - filter

Get Samsung RFG298HDRS PDF manuals and user guides View all Samsung RFG298HDRS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

01 setting up Adjusting the freezer drawer INSTALLing the WATER level DISPENSER line Adjustment part Freezer Drawer 1. L ocate the height-adjuster ( 1 ) in the freezer drawer. Unscrew the 8 Phillips screws ( 2 ) slightly to loosen the door. 1 2 A water dispenser with a filter is one of the helpful features on your new refrigerator. To help promote better health, the water filter removes unwanted particles from your water. However, it does not sterilize or destroy microorganisms. You may need to purchase a water purifying system to do that. In order for the ice maker to operate properly, a water pressure of 20~125 psi is required. Under normal conditions, a 170 cc (5.75 oz.) cup can be filled in about 10 seconds. If the refrigerator is installed in an area with low water pressure (below 20psi), you can install a booster pump to compensate for the low pressure. After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. Water line installation kits are available at extra cost from your dealer. We recommend using a water line installation kit that contains copper tubing and ¼" compression nut. 2. Loosen the controller screw ( 3 ) with a Phillips screwdriver (+). 3 Connecting to the water supply line 1. First, shut off the main water supply. 3. Find the best level to align the door slope. • A fter adjustment, tighten the controller screw and then the philips screws. 2. Locate the nearest cold water drinking line and install the pipe clamp and shut off valve. Cold water line Pipe clamp Shut off valve Example) The slope is about 0.08inch (2mm) as shown below. - Rotate the height adjuster to -2.0 to reduce the door slope. 3. Connect the water line installation kit to the shut off valve. Slope Reference plane Cold water line Pipe clamp Shut off valve Water line installation kit setting up _09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
setting up
_09
01 SETTING UP
ADJUSTING THE FREEZER DRAWER
LEVEL
1.
Locate the height-adjuster (
1
) in the freezer drawer.
Unscrew the 8 Phillips screws (
2
) slightly to loosen
the door.
2.
Loosen the controller
screw (
3
) with a Phillips
screwdriver (+).
3.
Find the best level to align the door slope.
•
After adjustment,
tighten the
controller screw
and then the
philips screws.
1
2
3
Freezer Drawer
Adjustment part
INSTALLING THE WATER
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need to
purchase a water purifying system to do that.
In order for the ice maker to operate properly, a water
pressure of 20~125 psi is required.
Under normal conditions, a 170 cc (5.75 oz.) cup can
be filled in about 10 seconds.
If the refrigerator is installed in an area with low water
pressure (below 20psi), you can install a booster pump
to compensate for the low pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator is
properly filled. To do this, press the water dispenser
lever until the water runs from the water outlet.
Water line installation kits are available at extra
cost from your dealer.
We recommend using a water line installation kit that
contains copper tubing and ¼” compression nut.
Connecting to the water supply line
1.
First, shut off the main water supply.
2.
Locate the nearest cold water drinking line and
install the pipe
clamp and shut
off valve.
3.
Connect the water line installation kit to the shut off
valve.
Example) The slope is about 0.08inch (2mm) as shown below.
- Rotate the height adjuster to -2.0 to reduce the door slope.
Slope
Reference
plane
Pipe clamp
Cold water line
Shut off valve
Shut off valve
Pipe clamp
Cold water line
Water line installation kit