Samsung WF363BTBEUF/A1 User Manual Ver.1.0 (English, French, Spanish) - Page 16

Step 1

Get Samsung WF363BTBEUF/A1 PDF manuals and user guides View all Samsung WF363BTBEUF/A1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

setting up your washer INSTALLING YOUR WASHER Before STEP 5 is complete, do not plug the power cord into a wall socket. CAUTION Packaging materials can be dangerous to children; keep all packaging material (plastic bags, WARNING polystyrene, etc.) well out of the reach of children. Installation flow chart Selecting a location Removing the shipping bolts (*Drum only) Connecting the water and the drain Please check again before steps. Adjusting the levelling feet Powering your washing machine Does your washer Finish the have excess vibration installation Yes or noise? No [Running a test cycle] Run a test cycle (Rinse+Spin) with small amount of laundary (about 4~5 Towels) STEP 1 Selecting a location Before you install the washer, make sure the location: • Has a hard, level surface without carpeting or flooring that may obstruct ventilation. • Has no dust, oil, detergent etc. • Is away from direct sunlight. • Has adequate ventilation. • Will not have temperatures at or below 32 ˚F or 0 ˚C. • Is away from heat sources such as oil or gas. • Has enough space so that the washer doesn't stand on its power cord. STEP 2 Removing the Shipping Bolts Before using your washer, you must remove all shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Fill the holes with the supplied plastic covers. 4. Keep the shipping bolts and spacers for future use. 16_ setting up your washer WF361_363_365-02832J-03_EN_20120829.indd Sec5:16 2012-08-31 12:38:17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
16_
setting up your washer
INSTALLING YOUR WASHER
Before STEP 5 is complete, do not plug the power cord into a wall socket.
Packaging materials can be dangerous to children; keep all packaging material (plastic bags,
polystyrene, etc.) well out of the reach of children.
Installation flow chart
Selecting a
location
Finish the
installation
Removing the shipping
bolts (*Drum only)
Connecting the water
and the drain
Adjusting the
levelling feet
Powering your washing
machine
[Running a test cycle]
Run a test cycle (Rinse+Spin) with
small amount of laundary
(about 4~5 Towels)
Yes
Please
check again
before
steps.
No
Does
your washer
have excess vibration
or noise?
STEP 1
Selecting a location
Before you install the washer, make sure the location:
•
Has a hard, level surface without carpeting or flooring that may obstruct ventilation.
• Has no dust, oil, detergent etc.
• Is away from direct sunlight.
• Has adequate ventilation.
•
Will not have temperatures at or below 32 ˚F or 0 ˚C.
•
Is away from heat sources such as oil or gas.
•
Has enough space so that the washer doesn’t stand on its power cord.
STEP 2
Removing the Shipping Bolts
Before using your washer, you must remove all shipping
bolts from the back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with
the spacer through the hole in the rear wall of your
washer. Repeat for each bolt.
3.
Fill the holes with the supplied plastic covers.
4.
Keep the shipping bolts and spacers for future use.
setting up your washer
WARNING
CAUTION
WF361_363_365-02832J-03_EN_20120829.indd Sec5:16
WF361_363_365-02832J-03_EN_20120829.indd
Sec5:16
2012-08-31
12:38:17
2012-08-31
12:38:17