Sanyo PLC XU73 Owners Manual - Page 45

On start, Lamp control, Remote control, To change the code for the projector

Get Sanyo PLC XU73 - XGA LCD Projector PDF manuals and user guides View all Sanyo PLC XU73 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Setting Setting On start When this function is "On", the projector will be automatically turned on just by connecting the AC power cord to a wall outlet. ✔Note: Be sure to turn the projector off properly (see "Turning Off the Projector" on page 19). If the projector is turned off in the incorrect sequence, the On start function does not operate properly. Lamp control This function allows you to change brightness of the screen. Normal ....normal brightness Auto ........brightness according with the input signal Eco ..........lower brightness reduces the lamp power consumption and extends the lamp life. Remote control This projector provides two different remote control codes; the factory-set, initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. When operating the projector in "Code 2", both the projector and the remote control must be switched to "Code 2". To change the code for the projector; Select either "Code 1" or "Code 2" in this Setting Menu. To change the code for the remote control; Press and hold both the MENU and IMAGE buttons together for 10 seconds or more. After changing the code, make sure the remote control operates properly. Remote control Press and hold MENU and IMAGE buttons for 10 seconds or more. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
45
Setting
On start
When this function is “On”, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
✔
Note:
Be sure to turn the projector off properly (see “Turning Off the
Projector” on page 19).
If the projector is turned off in the incorrect
sequence, the On start function does not operate properly.
Setting
Lamp control
Remote control
This projector provides two different remote control codes;
the factory-set, initial code (Code 1) and the secondary code
(Code 2).
This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
When operating the projector in “Code 2”,
both the
projector and the remote control must be switched to
“Code 2”.
To change the code for the projector;
Select either “Code 1” or “Code 2” in this Setting Menu.
To change the code for the remote control;
Press and hold both the MENU and IMAGE buttons
together for 10 seconds or more.
After changing the code,
make sure the
remote control operates properly.
Remote control
Press and hold
MENU and
IMAGE buttons
for 10 seconds or
more.
This function allows you to change brightness of the
screen.
Normal
....
normal brightness
Auto
........
brightness according with the input
signal
Eco
..........
lower brightness reduces the lamp
power consumption and extends the
lamp life.