Sanyo WXU700 Instruction Manual, PLC-WXU700A - Page 13

Remote Control Battery Installation, Remote Control Operating Range, Remote Control Code, RESET

Get Sanyo WXU700 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483074219
View all Sanyo WXU700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Part Names and Functions Remote Control Battery Installation 1 Open the battery compartment lid. 2 Install new batteries into the compartment. 3 Replace the compartment lid. Press the lid downward and slide it. Two AAA size batteries For correct polarity (+ and -), be sure battery terminals are in contact with pins in compartment. To ensure safe operation, please observe the following precautions : ● Use two (2) AAA or LR03 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control to moisture or heat. ● Do not drop the remote control. ● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Operating Range Point the remote control toward the projector when pressing the buttons. Maximum operating range for the remote control is about 16.4'(5 m) and 60 degrees in front of the projector. 16.4' (5 m) 30° 30° Remote control Remote Control Code The eight different remote control codes (Code 1 - Code 8) are assigned to this projector. Switching the remote control codes prevents interference from other remote controls when several projectors or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 58. 1 While pressing the MENU button, press the IMAGE button number of times corresponding to the remote control code. See the list below. 2 To initialize the remote control code, slide the RESET/ ON/ALL-OFF switch to RESET, and then to ON. The initial code is set to Code 1. While pressing the MENU button, press the IMAGE button number of times corresponding to the remote control code. Remote Control Code Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Number of Times Pressing IMAGE Button 1 2 3 4 5 6 7 8 MENU button IMAGE button RESET/ON/ALLOFF switch 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
13
Part Names and Functions
To ensure safe operation, please observe the following precautions :
● Use two (2) AAA or LR03 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Risk of an explosion if battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Press the lid
downward and slide it.
Open the battery
compartment lid.
Install new batteries
into the compartment.
Replace the
compartment lid.
Two AAA size batteries
For correct polarity
(+ and –), be sure
battery terminals are
in contact with pins in
compartment.
1
±
3
Point the remote control toward the projector when pressing
the buttons. Maximum operating range for the remote
control is about 16.4'(5 m) and 60 degrees in front of the
projector.
Remote Control Operating Range
Remote Control Battery Installation
16.4'
(5 m)
30°
Remote control
30°
While pressing the MENU
button, press the IMAGE
button number of times
corresponding to the remote
control code.
MENU button
IMAGE button
RESET/ON/ALL-
OFF switch
Remote Control Code
Remote Control Code
Number of Times
Pressing IMAGE
Button
Code 1
1
Code ±
±
Code 3
3
Code 4
4
Code 5
5
Code 6
6
Code 7
7
Code 8
8
The eight different remote control codes (Code 1 – Code 8) are assigned to this projector. Switching the remote
control codes prevents interference from other remote controls when several projectors or video equipment
next to each other are operated at the same time. Change the remote control code for the projector first before
changing that for the remote control. See "Remote control" in the Setting Menu on page 58.
While pressing the MENU button, press the IMAGE
button number of times corresponding to the remote
control code. See the list below.
1
To initialize the remote control code, slide the RESET/
ON/ALL-OFF switch to
RESET
, and then to
ON
. The
initial code is set to
Code 1
.
±