Sanyo WXU700 Instruction Manual, PLC-WXU700A - Page 70

Auto PC adjustment function does, not work°

Get Sanyo WXU700 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483074219
View all Sanyo WXU700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Appendix No image - Check the connection between your computer or video equipment and the projector. See pages 17-19. - See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes about 30 seconds to display an image after turning on the projector. See page 21. - Check the Input signal, color system, video system or computer system mode. - Make sure the temperature is not out of the specified Operating Temperature (41˚F-95˚F [5˚C-35˚C]). - When No Show function is operating, the image cannot be displayed. Press the NO SHOW button or any other button on the remote control. No sound - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. See page 27. - Press the Mute button. See page 27. - When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. - Is the image projected? You will hear the sound only when the image is projected. The color is strange. - Check the Input signal, color system, video system or computer system mode. - Make sure Blackboard is not selected on Image select menu. See pages 36, 43. Some displays are not seen during the operation. - Check the Display function. See page 49. Auto PC adjustment function does not work. - Check the Input signal. Auto PC adj.function can not work when 480p, 575p, 720p, 480i, 575i, 1035i or 1080i is selected (See page33) or when the digital signal is input into HDMI terminal. (See page 39) - Th e setting does not remain after Make sure can not be you selected Store after adjusting stored if not registered with Store. setting. Some See page 38, settings 45. turning off power. - Power management function can not work while Freeze or No Po wer management d oes not work. Show function is running. See page 56. Capture function does not work. - Check the connection and the input signal to see if there is signal. - Make sure Off is not selected at any function of "Auto setup". Auto setup does not work properly. See page 48. - Make sure On is not selected at the Ceiling function. See page 53. Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to Manual. Press the AUTO SETUP/CANCEL button on the top control. See pages 26,48. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
70
Appendix
– Check the connection between your computer or video equipment
and the projector. See pages 17-19.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 21.
–
Check the Input signal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (
41˚F–95˚F [5˚C–35˚C])
.
– When No Show function is operating, the image cannot be displayed.
Press the NO SHOW button or any other button on the remote control.
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 27.
– Press the Mute button. See page 27.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available.
– Is the image projected? You will hear the sound only when the image
is projected.
– Check the Input signal, color system, video system or computer
system mode.
– Make sure
Blackboard
is not selected on Image select
menu. See pages 36, 43.
– Check the Display function. See page 49.
– Check the Input signal. Auto PC adj.function can not work when
480p, 575p, 7±0p, 480i, 575i, 1035i
or
1080i
is selected (See page33)
or when the digital signal is input into HDMI terminal. (See page 39)
– Make sure you selected
Store
after adjusting setting. Some settings
can not be stored if not registered with Store. See page 38, 45.
– Power management function can not work while Freeze or No
Show function is running. See page 56.
– Check the connection and the input signal to see if there is signal.
– Make sure
Off
is not selected at any function of "Auto setup".
See page 48.
– Make sure
On
is not selected at the Ceiling function. See page 53.
– Make sure the Auto keystone function is not set to
Manual
. Press
the AUTO SETUP/CANCEL button on the top control. See pages 26,48.
No image
No sound
The color is strange°
Some displays are not seen during
the operation°
Auto PC adjustment function does
not work°
The setting does not remain after
turning off power°
Power management does not work°
Capture function does not work°
Auto setup does not work properly°
Auto keystone function does not
work even when the projector is
tipped°