Sanyo WXU700 Instruction Manual, PLC-WXU700A - Page 58

Remote control, Lamp control, Code 1, To change the code for the projector

Get Sanyo WXU700 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483074219
View all Sanyo WXU700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Setting Lamp control This function allows you to change brightness of the screen. Auto The brightness according to the input signal (between High and Eco mode). High Brighter than the Normal mode. Normal....... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Note: Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should set on both the projector and the remote control. For example, operating the projector in Code 7, the remote control code also must be switched to Code 7. To change the code for the projector Select a remote control code in this Setting Menu. To change the code for the remote control: While holding down the MENU button, press the IMAGE button the number of times corresponding to the remote control code for the projector. See "Remote Control Code" on page 13. Remote control Note: • When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector. • If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
58
Remote control
Lamp control
Remote control
The eight different remote control codes (
Code 1
-
Code 8
)
are assigned to the projector; the factory-set, initial code
(
Code 1
) and the other seven codes (
Code ±
to
Code 8
).
The same code should set on both the projector and the
remote control. For example, operating the projector in
Code 7
, the remote control code also must be switched to
Code 7
.
To change the code for the projector
Select a remote control code in this Setting Menu.
To change the code for the remote control:
While holding down the MENU button, press the IMAGE
button the number of times corresponding to the remote
control code for the projector. See “Remote Control Code”
on page 13.
Setting
Note:
• When different codes are set on the projector and on
the remote control, any operation cannot be made. In
that case, switch the code on the remote control to fit
the code on the projector.
• If the batteries are removed from the remote control for
a long period of time, the remote control code will
be reset.
This function allows you to change brightness of the screen.
Auto
...........
The brightness according to the input signal
(between High and Eco mode).
High
...........
Brighter than the Normal mode.
Normal
.......
Normal brightness
Eco
............
Lower brightness reduces the lamp power
consumption and extends the lamp life.
Note:
Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.