Sharp CD-ES9 Service Manual - Page 76

Sharp CD-ES9 Manual

Get Sharp CD-ES9 PDF manuals and user guides View all Sharp CD-ES9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

CSMECeDaHrvr-kEAiceSetP9M0T0aE/nCuRDal-E7S. 9F9LOWCHART CD-ES900/CD-ES99 [1] Troubleshooting 1. When the CD does not function The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the trouble shooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. 1. CD optical pickup Lens cleaner disc Parts code UDSKA0004AFZZ HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continuous to turn, press the stop button. Cleaning fluid CAUTION The CD lens cleaner should be effective for 30-50 operations, however if the brushes become worn out earlier then please the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD players or on computer CD-ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law. Cleaner disc 2. When a CD cannot be played 2.1. "E-CD01" is displayed. 1) Check the power to IC1 (LC78648E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 67 on IC1). 2) Does the pickup move to the PICKUP-IN Switch (SW1A) position? If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP). 2.2. Pressing the CD operation key is accepted, but playback does not occur. 1) Focus-HF system check 2) Tracking system check 3) Spin system check 4) PLL system check 5) Others 7 - 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
CD-ES900/CD-ES99
7 – 1
CD-ES900/CD-ES99
CD-ES900/CD-ES99
Service Manual
CD-ES900/CD-ES99
Market
E
CHAPTER 7.
FLOWCHART
[1] Troubleshooting
1. When the CD does not function
The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation.
When this section does not operate even after the above step is taken, check the following items.
Remove the cabinet and follow the trouble shooting instructions.
“Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting
any adjustment make certain that the lens is clean. If not, clean it as mentioned below.”
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
2. When a CD cannot be played
2.1. “E-CD01” is displayed.
1)
Check the power to IC1 (LC78648E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 67 on IC1).
2)
Does the pickup move to the PICKUP-IN Switch (SW1A) position?
If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP).
2.2. Pressing the CD operation key is accepted, but playback does not occur.
1)
Focus-HF system check
2)
Tracking system check
3)
Spin system check
4)
PLL system check
5) Others
Parts code
1.
CD optical pickup Lens cleaner disc
UDSKA0004AFZZ
HOW TO USE
CAUTION
Cleaning fluid
Cleaner disc
Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the
brush on the CD cleaner disc which has the mark next to it.
Place the CD cleaner disc onto the CD disc tray with the brush side down, then
press the play button.
You will hear music for about 20 seconds and the CD player will automatically stop.
If it continuous to turn, press the stop button.
1.
2.
3.
The CD lens cleaner should be effective for 30-50 operations, however if the
brushes become worn out earlier then please the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft
cloth.
Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the
event of this happening then drink and / or rinse with clean water and seek medical
advice.
The CD cleaner disc must not be used on car CD players or on computer CD-ROM
drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product
is prohibited by law.