Sharp CV-P10MX CV-P09LX , CV-P10LC , CV-P10MX , CV-P12LX Operation Manual - Page 14

Install Window Panel - installation

Get Sharp CV-P10MX - 9 500 BTU Portable A C PDF manuals and user guides
UPC - 074000662278
View all Sharp CV-P10MX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

INSTALL WINDOW PANEL Installation in a double-hung sash window (See page 14 for installation in a sliding sash window. ) Hole 1 Connect the rain guards to the insect guard net. Insert all three projections on each rain guard into the holes in the insect guard net. Side "A" will now be uppermost, as indicated in the diagram. Insect guard net Projection Rain guard "A" 2 Attach the guard combined above to the window panel Push the insect guard net firmly to ensure that its four projections fit into the holes in the window panel. "A" Side "A" will now be at the top, as indicated in the diagram. Projection Window panel 3 Cut the foam seal A (adhesive type) to the proper length and attach it to the window stool. Foam seal A (adhesive type) 4 Attach the window panel to the window stool. If the inner width of the window is between 22" (559mm) and 24" (609mm) inclusive. The window panel cannot be installed in windows less than 22" (559mm) wide, as you will be unable to shut the exhaust cover. (1) Remove the adjustment panel from the window panel, and cut the window panel to the same width as the window. Window panel (2) Open the window sash and place the window panel on the window stool (3) Secure the window panel to the window stool with 2 screws. 22"~ 24" Exhaust cover Cut Adjustment panel Window panel Window stool E-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
INSTALL WINDOW PANEL
Hole
Projection
Insect guard
net
Rain guard
"A"
Window panel
Projection
"A"
Window panel
E-12
Adjustment panel
Exhaust cover
Window
panel
Foam seal A
(adhesive type)
Installation in a double-hung sash window
(See page 14 for installation in a sliding sash window. )
1
Connect the rain guards to the insect
guard net.
Insert all three projections on each rain
guard into the holes in the insect guard net.
Side “A” will now be uppermost, as indi-
cated in the diagram.
2
Attach the guard combined above to the
window panel
Push the insect guard net firmly to ensure
that its four projections fit into the holes in
the window panel.
Side “A” will now be at the top, as indicated
in the diagram.
3
Cut the foam seal A (adhesive type) to
the proper length and attach it to the
window stool.
4
Attach the window panel to the window
stool.
If the inner width of the window is be-
tween 22" (559mm) and 24" (609mm)
inclusive.
The window panel cannot be installed in
windows less than 22" (559mm) wide, as
you will be unable to shut the exhaust cover.
(1)
Remove the adjustment panel from the
window panel, and cut the window
panel to the same width as the window.
(2) Open the window sash and place the win-
dow panel on the window stool
(3) Secure the window panel to the window
stool with 2 screws.
Cut
22"~ 24"
Window stool