Sharp CV-P10MX CV-P09LX , CV-P10LC , CV-P10MX , CV-P12LX Operation Manual - Page 8

Precautions - ac

Get Sharp CV-P10MX - 9 500 BTU Portable A C PDF manuals and user guides
UPC - 074000662278
View all Sharp CV-P10MX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

PRECAUTIONS Points to keep in mind when using your air conditioner. WARNINGS FOR USE • Install the air conditioner in accordance with the installation instructions in the latter section of this manual. • Do not modify any part of this product. • Do not insert anything into any part of the unit. • Ensure the power supply used has an appropriate voltage rating. Only use a three-pin grounded electrical AC socket rated 125V, 60Hz, and 15 amps or more as shown on the right. Use of a power supply with an improper voltage rating can result in damage to the unit and possibly fire. • Always use a fuse with the proper amp rating. Do not, under any circumstances, use wire, pins or other objects in place of a proper fuse. • In the event of any abnormality with the air conditioner (ex. a burning smell), turn it off immediately and disconnect the power supply. WARNING FOR POWER SUPPLY CORD • This air conditioner uses a plug with a built-in fuse. Read the precautions on the plug before using the air conditioner. • Always conduct a "Power Plug Check" (See Page 18) before use to confirm the power plug functions normally. • This power plug must only be plugged into an appropriate wall socket. Do not use in conjunction with any extension cords. • Push the power plug securely into the socket and make sure it is not loose. • Do not pull, deform, or modify the power supply cord, or immerse it in water. Pulling or misuse of the power supply cord can result in damage to the unit and cause electrical shock. • A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and not repaired. Replacement must be performed by manufacture's service agent in order to avoid a hazard. NOTE Radio or TV Interference If this room air conditioner should cause interference to radio or television reception, try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the room air conditioner and radio/TV receiver. • Connect the room air conditioner into an outlet on a circuit different from that to which the radio/TV receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This product fulfils the requirement of the International standard CISPR 11. In conformity with this standard, this product is classified as group 2 class B equipment. Group 2 means that the equipment intentionally generates radio-frequency in the form of electromagnetic radiation for electro-discharge machining equipment. Class B equipment means that the equipment suitable to be used in domestic establishments. E-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
PRECAUTIONS
Points to keep in mind when using your air conditioner.
WARNINGS FOR USE
•
Install the air conditioner in accordance with the installation instructions in the latter
section of this manual.
•
Do not modify any part of this product.
•
Do not insert anything into any part of the unit.
•
Ensure the power supply used has an appropriate voltage rating.
Only use a three-pin grounded electrical AC socket rated 125V, 60Hz,
and 15 amps or more as shown on the right.
Use of a power supply with an improper voltage rating can result in
damage to the unit and possibly fire.
•
Always use a fuse with the proper amp rating.
Do not, under any circumstances, use wire, pins or other objects in place of a proper fuse.
•
In the event of any abnormality with the air conditioner (ex. a burning smell), turn it
off immediately and disconnect the power supply.
WARNING FOR POWER SUPPLY CORD
•
This air conditioner uses a plug with a built-in fuse.
Read the precautions on the plug before using the air conditioner.
•
Always conduct a “Power Plug Check” (See Page 18) before use to confirm the power
plug functions normally.
•
This power plug must only be plugged into an appropriate wall socket. Do not use in
conjunction with any extension cords.
•
Push the power plug securely into the socket and make sure it is not loose.
•
Do not pull, deform, or modify the power supply cord, or immerse it in water.
Pulling or misuse of the power supply cord can result in damage to the unit and cause
electrical shock.
•
A damaged power supply cord must be replaced with a new power supply cord ob-
tained from the product manufacturer and not repaired.
Replacement must be per-
formed by manufacture's service agent in order to avoid a hazard.
NOTE
Radio or TV Interference
If this room air conditioner should cause interference to radio or television reception, try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the room air conditioner and radio/TV receiver.
•
Connect the room air conditioner into an outlet on a circuit different from that to which the
radio/TV receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This product fulfils the requirement of the International standard CISPR 11.
In conformity with this standard, this product is classified as group 2 class B equipment.
Group 2 means that the equipment intentionally generates radio-frequency in the form of
electromagnetic radiation for electro-discharge machining equipment.
Class B equipment means that the equipment suitable to be used in domestic establishments.
E-6