Sharp LC-60LE810UN Service Manual - Page 35

Sharp LC-60LE810UN Manual

Get Sharp LC-60LE810UN PDF manuals and user guides
UPC - 074000372580
View all Sharp LC-60LE810UN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

LCC-H40ALE8P10TUNER 5. ADJUSTMENT LC-40/46/52/60LE810UN (1st Edition) Service Manual [1] ADJUSTMENT PROCEDURE The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is required due to part replacement, make an adjustment according to the following procedure. 1. After replacement of any PWB unit and/or IC for repair, please note the following. • When replacing the following units, make sure to prepare the new units loaded with updated software. MAIN Unit: DKEYMF452FM01 • When replacing the LCD control PWB, perform the VCOM adjustment. 2. Upgrading of each microprocessor software CAUTION: Never "POWER OFF" the unit when software upgrade is ongoing. Otherwise the system may be damaged beyond recovery. 2.1. Software version upgrade The model employs the following software. • Main software (please use a software version after HLNRBxxx.USB (32" HLNRCxxx.USB).) • Monitor microprocessor software (please use a software version after HLNRA0x.USB and HLNIMxxx.BIN.) The main software, monitor microprocessor software can be upgraded by using a general-purpose USB Memory. The followings are the procedures for upgrading, explained separately for the main software, monitor microprocessor software. 2.2. Main software version upgrade 2.2.1 Get ready before you start • USB Memory of 128MB or higher capacity. • PC running on Windows 98/98SE/ME/2000/XP operating system. • USB Memory reader/writer or PC with a USB port. • The file system of a USB memory is FAT. (FAT32 supports) • Use the USB memory without other functions. (lock and memory reader...etc) 2.2.2 Preparations To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start. Follow the steps below and create the USB Memory for version upgrade. 1. Copy the file HLNRBxxx.USB (32" HLNRCxxx.USB). for version upgrade to the root directory (folder) of the USB Memory. NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade. Now the USB Memory for version upgrade is ready. 5 - 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
LC-40/46/52/60LE810UN (1st Edition)
5 – 1
LC-40LE810UN
Service Manual
CHAPTER 5.
ADJUSTMENT
[1] ADJUSTMENT PROCEDURE
The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is
required due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following.
•
When replacing the following units, make sure to prepare the new units loaded with updated software.
•
When replacing the LCD control PWB, perform the VCOM adjustment.
2. Upgrading of each microprocessor software
CAUTION: Never “POWER OFF” the unit when software upgrade is ongoing.
Otherwise the system may be damaged beyond recovery.
2.1. Software version upgrade
The model employs the following software.
•
Main software (please use a software version after HLNRBxxx.USB (32” HLNRCxxx.USB).)
•
Monitor microprocessor software (please use a software version after HLNRA0x.USB and HLNIMxxx.BIN.)
The main software, monitor microprocessor software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading, explained separately for the main software, monitor microprocessor software.
2.2. Main software version upgrade
2.2.1 Get ready before you start
•
USB Memory of 128MB or higher capacity.
•
PC running on Windows 98/98SE/ME/2000/XP operating system.
•
USB Memory reader/writer or PC with a USB port.
•
The file system of a USB memory is FAT. (FAT32 supports)
•
Use the USB memory without other functions. (lock and memory reader...etc)
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1.
Copy the file HLNRBxxx.USB (32” HLNRCxxx.USB). for version upgrade to the root directory (folder) of the USB Memory.
NOTE:
In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
MAIN Unit:
DKEYMF452FM01