Sharp PN-E471 PN-E421 PN-E471 Operation Manual - Page 30

■ To set from a PC, Set up process, Connecting your monitor to a PC, Specifying the PC's IP address

Get Sharp PN-E471 PDF manuals and user guides
UPC - 074000046955
View all Sharp PN-E471 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Controlling the Monitor with a PC (LAN) ■ To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC's IP address (3) Configure the monitor's LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor. 7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. • IP Address: 192.168.150.3 • Subnet Mask: 255.255.255.0 • Default Gateway: (leave blank) 8. Click [OK] and then reboot the PC. LAN terminal PC To LAN terminal LAN cable (commercially available, crossover) (2) Specifying the PC's IP address To configure the monitor's LAN settings, you must temporarily change the settings on the PC. This explanation is based on Windows XP. 1. Log on to the PC with an administrator account. 2. Click [Start], and then click "Control Panel". 3. Click "Network and Internet Connections", and then click "Network Connections". If you are using the classic display style, double-click on "Network Connections". 4. Right click on "Local Area Connection" and from the menu, click "Properties". 5. Click "Internet Protocol (TCP/IP)", and then click "Properties". 6. Make a note of the current IP address, subnet mask, and default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards. TIPS • This monitor is factory preset as shown below. IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 (3) Configuring the monitor's LAN settings Access the monitor using Internet Explorer. Controlling the monitor 1. Turn the power ON to the monitor. 2. Set RS-232C/LAN SELECT on the SETUP menu to LAN. PC operation 3. Launch Internet Explorer, in the "Address" box type "http://192.168.150.2/" and press the Enter key. You will be prompted to enter a user name and password. 4. Leave the user name and password boxes blank and click [OK]. E 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
30
E
30
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN
port on the PC and this
monitor.
LAN cable (commercially available, crossover)
To LAN terminal
PC
LAN terminal
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows XP.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “Network and Internet Connections”, and then click
“Network Connections”.
If you are using the classic display style, double-click on
“Network Connections”.
4. Right click on “Local Area Connection” and from the menu,
click “Properties”.
5. Click “Internet Protocol (TCP/IP)”, and then click
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.3
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
8. Click [OK] and then reboot the PC.
TIPS
•
This monitor is factory preset as shown below.
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
PC operation
3. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
You will be prompted to enter a user name and password.
4. Leave the user name and password boxes blank and click
[OK].
Controlling the Monitor with a PC (LAN)