Sony STRDG820 Operating Instructions - Page 33

To cancel Auto Calibration, Confirming/saving the, measurement results

Get Sony STRDG820 - STR AV Receiver PDF manuals and user guides
UPC - 027242727465
View all Sony STRDG820 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Press AUTO CAL. Measurement starts in 5 seconds. A count down is displayed. The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts. Measurement for Display Speaker existence TONE Speaker gain, distance, frequency T.S.P. response Subwoofer gain and distance WOOFER Tips • Operations other than turning the receiver on or off are deactivated during the measurement. • The measurements may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. To cancel Auto Calibration The Auto Calibration function will be canceled when you do the following during the measurement process: - Press ?/1 or POWER on the receiver. - Press the input buttons or turn the INPUT SELECTOR on the receiver. - Change the volume level. - Press MUTING. - Change the setting of the SPEAKERS (OFF/ A/B/A+B). - Connect headphones. - Press AUTO CAL again. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display Explanation result When the measurement process completes properly SAVE EXIT Proceed to step 2. When the measurement process fails E - xxx : See "Message xx list after Auto Calibration measurement" (page 35). 2 Press AMP and then press V/v repeatedly to select the item. Then, press . Item Explanation EXIT Exits the setting process without saving the measurement results. LEVEL INFO. Displays the measurement result for speaker level. DIST. INFO. Displays the measurement result for speaker distance. PHASE INFO. Displays the phase of each speaker (in phase/out of phase). See "When you select "PHASE INFO."" (page 34). WARN CHECK Displays warning concerning the measurement results. See "When you select "WARN CHECK"" (page 36). SAVE EXIT Saves the measurement results and exits the setting process. RETRY Performs the Auto Calibration again. continued 33US Getting Started

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
33
US
Getting Started
Press AUTO CAL.
Measurement starts in 5 seconds. A count
down is displayed.
The measurement process will take
approximately 30 seconds to complete.
The table below shows the display when
measurement starts.
Tips
• Operations other than turning the receiver on or off
are deactivated during the measurement.
• The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press
?
/
1
or POWER on the receiver.
– Press the input buttons or turn the INPUT
SELECTOR on the receiver.
– Change the volume level.
– Press MUTING.
–
Change the setting of the SPEAKERS (OFF/
A/B/A+B).
– Connect headphones.
– Press AUTO CAL again.
1
Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
2
Press AMP and then press
V
/
v
repeatedly to select the item.
Then, press
Measurement for
Display
Speaker existence
TONE
Speaker gain, distance, frequency
response
T.S.P.
Subwoofer gain and distance
WOOFER
Confirming/saving the
measurement results
Measurement
result
Display
Explanation
When the
measurement
process
completes
properly
SAVE EXIT
Proceed to step
2.
When the
measurement
process fails
E -
xxx
:
xx
See “Message
list after Auto
Calibration
measurement”
(page 35).
Item
Explanation
EXIT
Exits the setting process
without saving the
measurement results.
LEVEL INFO.
Displays the measurement
result for speaker level.
DIST. INFO.
Displays the measurement
result for speaker distance.
PHASE INFO.
Displays the phase of each
speaker (in phase/out of
phase). See “When you
select “PHASE INFO.””
(page 34).
WARN CHECK
Displays warning
concerning the
measurement results. See
“When you select “WARN
CHECK”” (page 36).
SAVE EXIT
Saves the measurement
results and exits the setting
process.
RETRY
Performs the Auto
Calibration again.
continued