Sony XAV-AX8500 Operating Instructions - Page 17

Adjusting the depth of the display, position, Adjusting the display angle subtilt

Get Sony XAV-AX8500 PDF manuals and user guides View all Sony XAV-AX8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

 Setting up the display The mounting positions of the display can be adjusted. Depth (within 20 mm (13/16 in), in 3 steps) Height (within 60 mm (2 3/8 in), in 7 steps) Angle (tilt) (-15° to +15°, continuously) Angle (swivel) (-15° to +15°, continuously) 2 Slide the connector bracket to decide the appropriate depth position. Adjustable depth: within 20 mm (13/16 in) (), in 3 steps, in 10 mm (13/32 in) pitch (). ɸ 321 ɹɹ Bracket positions 1 to 3 for the display: 1: Slide-out position 2: Intermediate position 3: Slide-in position 3 At the desired position, tighten the 3 screws firmly to secure the connector bracket. Width (within 25 mm (1 in), in 5 steps) Adjusting the depth of the display position 1 Loosen the 3 pre-installed screws for depth adjustment (on top and both sides). Tighten the screws firmly. When you tighten a screw, be careful not to apply too much torque as doing so may damage the screw (the torque value should be from 1.5 N•m to 2.0 N•m). Adjusting the display angle (subtilt) 1 Remove the 2 pre-installed screws for angle adjustment (on both sides). Pre-installed screws Slightly loosen the screws until you can slide the connector bracket. Do not remove the screws from the bracket. Doing so may damage the parts. Pre-installed screws 17EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
17
EN
The mounting positions of the display can be
adjusted.
Adjusting the depth of the display
position
1
Loosen the 3 pre-installed screws for depth
adjustment (on top and both sides).
Slightly loosen the screws until you can slide the
connector bracket. Do not remove the screws
from the bracket. Doing so may damage the
parts.
2
Slide the connector bracket to decide the
appropriate depth position.
Adjustable depth: within 20 mm (
13
/
16
in) (
), in
3 steps, in 10 mm (
13
/
32
in) pitch (
).
Bracket positions 1 to 3 for the display:
1: Slide-out position
2: Intermediate position
3: Slide-in position
3
At the desired position, tighten the 3 screws
firmly to secure the connector bracket.
Tighten the screws firmly.
When you tighten a screw, be careful not to
apply too much torque as doing so may damage
the screw (the torque value should be from
1.5 N•m to 2.0 N•m).
Adjusting the display angle (subtilt)
1
Remove the 2 pre-installed screws for angle
adjustment (on both sides).
Setting up the display
Depth
(within 20 mm
(
13
/
16
in), in 3 steps)
Height
(within 60 mm
(2
3
/
8
in), in 7 steps)
Angle (tilt)
(-15° to +15°,
continuously)
Angle (swivel)
(-15° to +15°, continuously)
Width
(within 25 mm (1 in), in 5 steps)
Pre-installed screws
3
2
1
Pre-installed screws