Sony XAV-AX8500 Operating Instructions - Page 21

Adjusting the display tilt and swivel, angle, Fuse replacement, to secure the cover.

Get Sony XAV-AX8500 PDF manuals and user guides View all Sony XAV-AX8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3 Slide the joint cover out to protect the mounting base of the display, then tighten the fixing screw  to secure the cover. Joint cover  Adjusting the display tilt and swivel angle After the display is installed, grip the correct parts of the display and adjust the display angle in the tilt and swivel directions. Where to place your hands when gripping the display: Front Rear   Notes • When adjusting the angle of the display, grip the top, left, or right side of the display with both hands as indicated by the shaded areas. • When adjusting the angle of the display, be careful not to get your fingers caught. Tighten the screw firmly. When you tighten a screw, be careful not to apply too much torque as doing so may damage the screw (the torque value should be from 1.5 N•m to 2.0 N•m). 4 Attach the rear panel covers  along the guides for protection.  • Do not adjust the display angle while driving. • Adjust the display angle so that the display does not obstruct moving parts of the vehicle such as the shift lever and steering wheel. Fuse replacement When replacing the fuse, be sure to Fuse (10 A) use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Notes • Be sure to use the specified screws. • If the display appears to rattle, tighten the screws periodically. 21EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
21
EN
3
Slide the joint cover out to protect the
mounting base of the display, then tighten
the fixing screw
to secure the cover.
Tighten the screw firmly.
When you tighten a screw, be careful not to
apply too much torque as doing so may damage
the screw (the torque value should be from
1.5 N•m to 2.0 N•m).
4
Attach the rear panel covers
along the
guides for protection.
Notes
• Be sure to use the specified screws.
• If the display appears to rattle, tighten the screws
periodically.
After the display is installed, grip the correct parts
of the display and adjust the display angle in the tilt
and swivel directions.
Where to place your hands when gripping the
display:
Notes
• When adjusting the angle of the display, grip the top, left,
or right side of the display with both hands as indicated by
the shaded areas.
• When adjusting the angle of the display, be careful not to
get your fingers caught.
• Do not adjust the display angle while driving.
• Adjust the display angle so that the display does not
obstruct moving parts of the vehicle such as the shift lever
and steering wheel.
When replacing the fuse, be sure to
use one matching the amperage
rating stated on the original fuse.
If the fuse blows, check the power
connection and replace the fuse.
If the fuse blows again after
replacement, there may be an
internal malfunction. In such a case, consult your
nearest Sony dealer.
Joint cover
Adjusting the display tilt and swivel
angle
Fuse replacement
Front
Rear
Fuse (10 A)