Sony XAV-AX8500 Operating Instructions - Page 18

Adjusting the height of the display, position, Remove the 4 pre-installed screws

Get Sony XAV-AX8500 PDF manuals and user guides View all Sony XAV-AX8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

2 Adjust the mounting position of the screw located where the line () on the swivel cover is closest to the ground and oriented horizontally. ɸ Note Install the pre-installed screws in the correct positions. Installing the screws in incorrect positions will cause the display to rotate diagonally when you swivel it. When adjusting to swivel +15°: Correct position Incorrect position The installation angle on the vehicle is determined based on the vehicle, and the position of the pre-installed screw is determined accordingly. Screw holes to use for each mounting angle: Adjusting the height of the display position 1 Remove the 4 pre-installed screws for height adjustment (on both sides). 1 A 2 3 B 4 C 2-A 3-B 4-C 1-A Pre-installed screws 2 Slide the connector bracket up or down to decide the appropriate height position. Adjustable height: within 60 mm (2 3/8 in) (), in 7 steps, in 10 mm (13/32 in) pitch (). ɹ ɹ ɹ ɹ ɸ 3 At the desired position, tighten the 2 screws through the screw holes (upper, center, or lower) that match the display angle. 18EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
18
EN
2
Adjust the mounting position of the screw
located where the line (
) on the swivel
cover is closest to the ground and oriented
horizontally.
The installation angle on the vehicle is
determined based on the vehicle, and the
position of the pre-installed screw is determined
accordingly.
Screw holes to use for each mounting angle:
3
At the desired position, tighten the 2 screws
through the screw holes (upper, center, or
lower) that match the display angle.
Note
Install the pre-installed screws in the correct positions.
Installing the screws in incorrect positions will cause the
display to rotate diagonally when you swivel it.
Adjusting the height of the display
position
1
Remove the 4 pre-installed screws for
height adjustment (on both sides).
2
Slide the connector bracket up or down to
decide the appropriate height position.
Adjustable height: within 60 mm (2
3
/
8
in) (
),
in 7 steps, in 10 mm (
13
/
32
in) pitch (
).
A
1
2
3
4
C
B
2-A
3-B
4-C
1-A
Correct position
Incorrect position
When adjusting to swivel +15°:
Pre-installed screws