Troy-Bilt CSV 060 Operation Manual - Page 17

Troubleshooting - replacement bag

Get Troy-Bilt CSV 060 PDF manuals and user guides View all Troy-Bilt CSV 060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Troubleshooting 8 Problem Cause Remedy Engine Fails to start Engine runs erratic Engine overheats Occasional skips (hesitates) at high speed Excessive Vibration Unit does not discharge 1. Throttle lever (if equipped) not in correct starting position. 2. Engine switch (if equipped) in OFF position. 3. Spark plug wire disconnected. 4. Choke not in CHOKE position (if equipped). 5. Fuel tank empty or stale fuel. 6. Fuel shut-off valve closed (if equipped). 7. Faulty spark plug. 8. Bag/chute switch button is not fully depressed. 1. Spark plug boot loose. 2. Unit running on CHOKE (if equipped). 3. Blocked fuel line or stale fuel. 4. Low engine RPM. 5. Water or dirt in fuel system. 6. Dirty air cleaner. 7. Carburetor out of adjustment. 1. Engine oil level low. 2. Dirty air cleaner. 1. Spark plug gap too close. 2. Carburetor idle mixture adjustment improperly set. 1. Loose parts or damaged impeller. 1. Discharge area clogged. 2. Foreign object lodged in impeller. Rate of discharge slows considerably or composition of discharged material changes 3. Low engine RPM. 4. Vacuum bag is full. 1. Low engine RPM. 2. Chipper blade dull. 1. Move throttle lever to FAST or START position. 2. Move engine switch to ON position. 3. Connect wire to spark plug. 4. Move choke lever to CHOKE position. 5. Fill tank with clean, fresh gasoline. 6. Turn on fuel shut-off valve. 7. Clean, adjust gap, or replace. 8. Make certain the bag is correctly secured, and the bag/chute switch button is fully depressed. 1. Connect and tighten spark plug boot. 2. Move choke lever to OFF position. 3. Clean fuel line; fill tank with clean, fresh gasoline. 4. Always run engine at full throttle (if equipped). 5. Drain fuel tank. Refill with fresh fuel. 6. Refer to engine manual. 7. See authorized service dealer. 1. Fill crankcase with proper oil. 2. Refer to engine manual. 1. Remove spark plug and adjust gap to .030". 2. See authorized service dealer. 2. See authorized service dealer. 1. Stop engine immediately and disconnect spark plug wire. Clean flail screen and inside of discharge opening. 2. Stop engine and disconnect spark plug wire. Remove lodged object. 3. Always run engine at full throttle. 4. Empty bag. 1. Always run engine at full throttle. 2. Replace chipper blade or see your authorized service dealer. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Troubleshooting
8
17
Problem
Cause
Remedy
Engine Fails to start
Throttle lever (if equipped) not in correct
1.
starting position.
Engine switch (if equipped) in OFF position.
2.
Spark plug wire disconnected.
3.
Choke not in CHOKE position (if equipped).
4.
Fuel tank empty or stale fuel.
5.
Fuel shut-off valve closed (if equipped).
6.
Faulty spark plug.
7.
Bag/chute switch button is not fully
8.
depressed.
Move throttle lever to FAST or START
1.
position.
Move engine switch to ON position.
2.
Connect wire to spark plug.
3.
Move choke lever to CHOKE position.
4.
Fill tank with clean, fresh gasoline.
5.
Turn on fuel shut-off valve.
6.
Clean, adjust gap, or replace.
7.
Make certain the bag is correctly secured,
8.
and the bag/chute switch button is fully
depressed.
Engine runs erratic
Spark plug boot loose.
1.
Unit running on CHOKE (if equipped).
2.
Blocked fuel line or stale fuel.
3.
Low engine RPM.
4.
Water or dirt in fuel system.
5.
Dirty air cleaner.
6.
Carburetor out of adjustment.
7.
Connect and tighten spark plug boot.
1.
Move choke lever to OFF position.
2.
Clean fuel line; fill tank with clean, fresh
3.
gasoline.
Always run engine at full throttle (if
4.
equipped).
Drain fuel tank. Refill with fresh fuel.
5.
Refer to engine manual.
6.
See authorized service dealer.
7.
Engine overheats
Engine oil level low.
1.
Dirty air cleaner.
2.
Fill crankcase with proper oil.
1.
Refer to engine manual.
2.
Occasional skips
(hesitates) at
high speed
Spark plug gap too close.
1.
Carburetor idle mixture adjustment
2.
improperly set.
Remove spark plug and adjust gap to .030”.
1.
See authorized service dealer.
2.
Excessive Vibration
Loose parts or damaged impeller.
1.
See authorized service dealer.
2.
Unit does not discharge
Discharge area clogged.
1.
Foreign object lodged in impeller.
2.
Low engine RPM.
3.
Vacuum bag is full.
4.
Stop engine immediately and disconnect
1.
spark plug wire. Clean flail screen and inside
of discharge opening.
Stop engine and disconnect spark plug wire.
2.
Remove lodged object.
Always run engine at full throttle.
3.
Empty bag.
4.
Rate of discharge slows
considerably or composition
of discharged material
changes
Low engine RPM.
1.
Chipper blade dull.
2.
Always run engine at full throttle.
1.
Replace chipper blade or see your authorized
2.
service dealer.