Whirlpool WGD8300S Use and Care Manual - Page 14

select the Air Only Temperature

Get Whirlpool WGD8300S PDF manuals and user guides View all Whirlpool WGD8300S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

7. Reassemble the inner and outer door assemblies with the 6 screws. f. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See "Level Dryer." Reverse the strike 1. Use a small flat-blade screwdriver to remove plug strip from the dryer door opening. Slide the head of the screwdriver under the plugs, being certain not to scratch the dryer surface. Lift up. 2. Remove the strike. 3. Insert strike and plug strip on the opposite side. A A. Plug strip (cannot be seen from this angle) B. Door strike Reinstall the door 1. Reattach door to dryer front panel with the 4 screws. ® Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord, Failure to follow these instructions can result in death, fire, or electrical shock. 6. Plug into a grounded 3 prong outlet. Turn on power. 7. Remove any protective film or tape remaining on the dryer. 8. Read "Dryer Use." 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. f0. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting. If the dryer will not start, check the following: • Dryer is plugged into a grounded 3 prong outlet. • Electrical supply is connected. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. f 1. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open. • If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above. • If the gas supply line shutoff valve is open, contact a qualified technician. A. Dryer front panel B. Door assembly 2. Check for fingerprints on the glass. Clean the glass if necessary. 3. Close door and check that it latches securely. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
7.
Reassemble
the inner and outer door assemblies
with the
6 screws.
f.
Check that all parts are now installed.
If there is an extra part,
go back through
the steps to see which step was skipped.
2.
Check that you have all of your tools.
3.
Dispose
of/recycle
all packaging
materials.
4.
Check the dryer's final location.
Be sure the vent is not
crushed
or kinked.
5.
Check that the dryer
is level. See "Level
Dryer."
Reverse
the strike
1.
Use a small flat-blade
screwdriver
to remove plug strip from
the dryer door opening.
Slide the head of the screwdriver
under the plugs, being certain not to scratch
the dryer
surface.
Lift up.
2.
Remove the strike.
3.
Insert
strike and plug strip on the opposite
side.
A
A. Plug strip (cannot be seen from this angle)
B. Door strike
Reinstall the door
1.
Reattach
door to dryer front panel with the 4 screws.
®
Electrical
Shock
Hazard
Plug into
a grounded
3
prong
outlet.
Do not remove
ground
prong.
Do not use an adapter.
Do
not
use an extension
cord,
Failure
to follow
these
instructions
can result
in
death,
fire, or
electrical
shock.
6.
Plug into a grounded
3 prong outlet. Turn on power.
7.
Remove
any protective
film or tape remaining
on the dryer.
8.
Read "Dryer Use."
9.
Wipe the dryer drum
interior thoroughly
with a damp cloth to
remove any dust.
f0.
Select a Timed
Dry heated cycle, and start the dryer. Do not
select the Air Only Temperature
setting.
If the dryer
will
not start,
check
the
following:
•
Dryer is plugged
into a grounded
3 prong outlet.
•
Electrical
supply
is connected.
•
Household
fuse is intact and tight, or circuit
breaker has
not tripped.
•
Dryer door
is closed.
f 1. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle
and
close door. If you do not feel heat, turn off the dryer
and
check that the gas supply
line shutoff
valve is open.
•
If the gas supply
line shutoff
valve is closed, open it, then
repeat the 5-minute
test as outlined
above.
•
If the gas supply
line shutoff
valve is open, contact
a
qualified
technician.
A. Dryer front panel
B. Door assembly
2.
Check for fingerprints
on the glass. Clean the glass if
necessary.
3.
Close door and check that it latches
securely.
14