Yamaha NX-N500 NX-N500 Owners Manual - Page 18

Connecting to the network using a, cable, Sharing the iOS device setting - reset

Get Yamaha NX-N500 PDF manuals and user guides View all Yamaha NX-N500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

PREPARATIONS ■ Connecting to the network using a cable As a default, this unit will automatically make a network connection when it is connected to a wired router and turned on. ■ Sharing the iOS device setting You can easily setup a wireless connection by applying the connection settings on iOS devices (iPhone/iPod touch). Before proceeding, confirm that your iOS device is connected to a wireless router (access point). • When connecting to the network using a cable, a network connection will be established regardless of whether the WIRELESS switch on the rear panel is set to "AUTO" or "OFF". • If a wireless connection has already been established with this unit, the WIRELESS switch on the unit must first be set to "OFF". After turning off the unit and connecting the network cable, set the WIRELESS switch to "OFF", and then turn the unit on again. In order to use Bluetooth, turn on the unit before setting the WIRELESS switch to "AUTO". 1 Make sure that this unit is connected to the router with a cable. 2 Press z (power) on the remote control to turn on the unit. The network settings are automatically specified. While the settings are being specified, the status indicator on the front panel flashes in green. Left speaker (front panel) Green (flashing) • In order to share Wi-Fi settings, the iOS device must be installed with iOS 7 or later. • Following the procedure below will reset specified account information and registered preset settings. • If network settings have already been specified, reset the network connection, and then follow the procedure below. • If a wired connection has already been established with this unit, the WIRELESS switch on the unit must first be set to "OFF" while the unit is on. After disconnecting the network cable, set the WIRELESS switch to "AUTO". 1 Set the WIRELESS switch on the rear panel to "AUTO". Left speaker (rear panel) R CH AUDIO OUT AUTO OFF WIRELESS WIRELESS switch AC IN GAIN CONNECT WIRELESS DIRECT SOURCE MIN MAX When the connection is established, the status indicator on the front panel changes to lit. Left speaker (front panel) 2 Press z (power) on the remote control to turn on the unit. The status indicator on the front panel flashes in pink. Left speaker (front panel) Green (lit) Pink (flashing) When this unit detects an iOS device, a connection confirmation message appears. 3 Tap "Allow" in the iOS device screen. When the connection is established, the status indicator on the front panel lights up in green. Left speaker (front panel) Green (lit) English En 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
En
15
PREPARATIONS
English
■
Connecting to the network using a
cable
As a default, this unit will automatically make a network
connection when it is connected to a wired router and turned
on.
•
When connecting to the network using a cable, a network connection will
be established regardless of whether the WIRELESS switch on the rear
panel is set to “AUTO” or “OFF”.
•
If a wireless connection has already been established with this unit, the
WIRELESS switch on the unit must first be set to “OFF”. After turning off
the unit and connecting the network cable, set the WIRELESS switch to
“OFF”, and then turn the unit on again. In order to use
Bluetooth
, turn on
the unit before setting the WIRELESS switch to “AUTO”.
1
Make sure that this unit is connected to the
router with a cable.
2
Press
z
(power) on the remote control to turn
on the unit.
The network settings are automatically specified. While
the settings are being specified, the status indicator on
the front panel flashes in green.
When the connection is established, the status indicator
on the front panel changes to lit.
■
Sharing the iOS device setting
You can easily setup a wireless connection by applying the
connection settings on iOS devices (iPhone/iPod touch).
Before proceeding, confirm that your iOS device is connected
to a wireless router (access point).
•
In order to share Wi-Fi settings, the iOS device must be installed with iOS
7 or later.
•
Following the procedure below will reset specified account information
and registered preset settings.
•
If network settings have already been specified, reset the network
connection, and then follow the procedure below.
•
If a wired connection has already been established with this unit, the
WIRELESS switch on the unit must first be set to “OFF” while the unit is
on. After disconnecting the network cable, set the WIRELESS switch to
“AUTO”.
1
Set the WIRELESS switch on the rear panel to
“AUTO”.
2
Press
z
(power) on the remote control to turn
on the unit.
The status indicator on the front panel flashes in pink.
When this unit detects an iOS device, a connection
confirmation message appears.
3
Tap “Allow” in the iOS device screen.
When the connection is established, the status indicator
on the front panel lights up in green.
Green (flashing)
Left speaker (front panel)
Green (lit)
Left speaker (front panel)
R CH
AUDIO OUT
AUTO
OFF
WIRELE
SS
CONNECT
S
OURCE
GAIN
AC IN
MAX
MIN
WIRELE
SS
DIRECT
Left speaker (rear panel)
WIRELESS switch
Pink (flashing)
Left speaker (front panel)
Green (lit)
Left speaker (front panel)