AEG BP8715001M Product Manual - Page 29

Installing the shelf supports, Pyrolysis, Oven lamp

Page 29 highlights

1 2 ENGLISH 29 2. Pull the rear end of the shelf support away from the side wall and remove it. Installing the shelf supports Install the shelf supports in the opposite sequence. The rounded ends of the shelf supports must point to the front. 12.2 Pyrolysis CAUTION! If a hob is installed with the appliance, do not use it at the same time as the Pyrolysis function. It can cause damage to the appliance. For steam models only: before you start the cleaning procedure, make sure that the water tank is completely empty. Refer to "Emptying the water tank". Remove all accessories from the appliance. The cleaning procedure cannot start: • If you do not remove the shelf support runners or telescopic shelf runners (if present). • If you do not close the appliance door correctly. • If you do not unplug the core temperature sensor (if present). When the Pyrolysis starts the appliance door is locked. After the function finishes the door is locked for the cool down phase. Some of the appliance functions are not available during the cool down phase. WARNING! When the Pyrolysis finishes the appliance is very hot. Let it cool down. There is a risk of burns Pyrolysis : 1. Remove the worst of the residual dirt manually. 2. Activate the appliance and choose the Pyrolysis function in the main menu. Press OK to confirm. 3. Touch or to set the length for the procedure: - Quick - 1h for a low degree of dirt - Normal - 1h 30 min for a usual de- gree of dirt - Intense - 2h 30 min for a high de- gree of dirt 4. Press OK to confirm. 12.3 Oven lamp WARNING! Be careful when you change the oven lamp. There is a risk of electrical shock. Before you change the oven lamp: • Deactivate the oven. • Remove the fuses in the fuse box or deactivate the circuit breaker. Put a cloth on the bottom of the oven to prevent damage to the oven light and glass cover. Always hold the halogen lamp with a cloth to prevent grease residue from burning on the lamp. 1. Turn the glass cover counterclockwise to remove it. 2. Clean the glass cover. 3. Replace the oven light bulb with an applicable 300 °C heat-resistant oven light bulb. Use the same oven lamp type. 4. Install the glass cover.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

2
1
2.
Pull the rear end of the shelf sup-
port away from the side wall and re-
move it.
Installing the shelf supports
Install the shelf supports in the opposite
sequence.
The rounded ends of the shelf
supports must point to the front.
12.2
Pyrolysis
CAUTION!
If a hob is installed with the ap-
pliance, do not use it at the same
time as the Pyrolysis function. It
can cause damage to the appli-
ance.
For steam models only: before
you start the cleaning procedure,
make sure that the water tank is
completely empty. Refer to
“Emptying the water tank”.
Remove all accessories from the
appliance.
The cleaning procedure cannot start:
If you do not remove the shelf support
runners or telescopic shelf runners (if
present).
If you do not close the appliance door
correctly.
If you do not unplug the core temper-
ature sensor (if present).
When the Pyrolysis starts the ap-
pliance door is locked. After the
function finishes the door is
locked for the cool down phase.
Some of the appliance functions
are not available during the cool
down phase.
WARNING!
When the Pyrolysis finishes the
appliance is very hot. Let it cool
down. There is a risk of burns
Pyrolysis :
1.
Remove the worst of the residual dirt
manually.
2.
Activate the appliance and choose
the Pyrolysis function in the main
menu. Press
OK
to confirm.
3.
Touch
or
to set the length
for the procedure:
Quick - 1h for a low degree of dirt
Normal - 1h 30 min for a usual de-
gree of dirt
Intense - 2h 30 min for a high de-
gree of dirt
4.
Press
OK
to confirm.
12.3
Oven lamp
WARNING!
Be careful when you change the
oven lamp. There is a risk of elec-
trical shock.
Before you change the oven lamp:
Deactivate the oven.
Remove the fuses in the fuse box or
deactivate the circuit breaker.
Put a cloth on the bottom of the
oven to prevent damage to the
oven light and glass cover.
Always hold the halogen lamp
with a cloth to prevent grease
residue from burning on the
lamp.
1.
Turn the glass cover counterclock-
wise to remove it.
2.
Clean the glass cover.
3.
Replace the oven light bulb with an
applicable 300 °C heat-resistant
oven light bulb.
Use the same oven lamp type.
4.
Install the glass cover.
ENGLISH
29