Alpine CDE-136BT Owner's Manual (english) - Page 15

1 Press and hold AUDIOSETUP for at least 2 seconds to activate the SETUP mode. 2 Turn the Rotary encoder to select AUDIO, and then press ENTER. BLUETOOTH  GENERAL  AUDIO  DISPLAY  iPod & USB 3 Turn the Rotary encoder to select the desired sound setting menu, and then press ENTER. FACTORY EQ*1/*2  3BAND EQ*1/*3  HPF*1  SUBWOOFER  SUBW LPF*4  SUBW PHASE*4  SUBW SYS*4 *1 Adjustment cannot be performed when DEFEAT is set to ON. *2 Any changes made to either FACTORY EQ or 3BAND EQ are reflected in the others' settings. *3 In step 3, three sound adjustment items (Bass, Mid and Treble) can be selected in 3BAND EQ mode, turn the Rotary encoder to select the desired item, and then press ENTER to continue to step 4. *4 These functions are inoperable when Subwoofer is set to OFF. 4 Turn the Rotary encoder to change the setting, and then press ENTER. (e.g. Select SUBWOOFER ON or SUBWOOFER OFF) 5 Press and hold AUDIOSETUP for at least 2 seconds to return to normal mode. Notes • Pressing  returns to the previous Sound menu mode. • If no operation is performed for 60 seconds, Sound menu mode is canceled. Equalizer Presets (FACTORY EQ) 10 typical equalizer settings are preset at the factory for a variety of musical source material. USER settings are created in the 3BAND EQ mode. USER  FLAT (Initial setting)  POPS  ROCK  NEWS  JAZZ  ELEC DANCE  HIP HOP  EASY LIS  COUNTRY  CLASSICAL Adjusting the Parametric Equalizer Curve (3BAND EQ) You can modify the Equalizer settings to create a response curve more appealing to your personal taste. The setting of Bass, Mid and Treble can be adjusted in this mode. Setting the Bass Control 1 After selecting BASS from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Bass setting item, and then press ENTER. WIDTH (Q)  CENTER FRQ  LEVEL 2 Turn the Rotary encoder to select the desired setting value, and then press ENTER. 3 Press  to return to the previous step.  Setting the Bass Bandwidth (WIDTH (Q)) Turn the Rotary encoder to select the desired bass bandwidth. WIDE 0.50  MEDIUM 1.00  MEDIUM 1.50 (Initial setting)  NARROW 2.00 Changes the boosted bass bandwidth to wide or narrow. A wider setting will boost a wide range of frequencies above and below the center frequency. A narrower setting will boost only frequencies near the center frequency.  Setting the Bass Center Frequency (CENTER FRQ) Turn the Rotary encoder to select the desired bass center frequency. 60 (Hz)  80 (Hz)  100 (Hz) (Initial setting)  120 (Hz) Emphasizes the displayed bass frequency ranges.  Setting the Bass Level Turn the Rotary encoder to select the desired bass level (-7~+7)*. You can emphasize or weaken the bass level. * The adjustment can also be made by pressing AUDIO. Refer to "Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/ Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat" on page 14. Setting the Mid Control 1 After selecting MID from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Mediant setting item, and then press ENTER. WIDTH (Q)  CENTER FRQ  LEVEL 2 Turn the Rotary encoder to select the desired setting value, and then press ENTER. 3 Press  to return to the previous step.  Setting the Mid Bandwidth (WIDTH (Q)) Turn the Rotary encoder to select the desired Mid bandwidth. WIDE 0.75  MEDIUM 1.00  MEDIUM 1.25  NARROW 1.50 (Initial setting)  Setting the Mid Center Frequency (CENTER FRQ) Turn the Rotary encoder to select the desired Mid center frequency. 500 (Hz)  1.0k (Hz) (Initial setting) 1.5k (Hz)  2.5k (Hz)  Setting the Mid Level Turn the Rotary encoder to select the desired Mid level (-7 ~ +7)*. You can emphasize or weaken the Mid level. * The adjustment can also be made by pressing AUDIO. Refer to "Adjusting Subwoofer Level/Bass Level/Mid Level/Treble Level/ Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat" on page 14. Setting the Treble Control 1 After selecting TREBLE from the 3BAND EQ adjustment mode, turn the Rotary encoder to select the desired Treble setting item, and then press ENTER. WIDTH (Q)  CENTER FRQ  LEVEL 2 Turn the Rotary encoder to select the desired setting value, and then press ENTER. 15-EN