Amana ART318FFDW Installation Instructions - Page 10

Top/Upright freezer models continued

Get Amana ART318FFDW PDF manuals and user guides View all Amana ART318FFDW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Top/Upright freezer models (continued) Refer to the side diagrams for the following steps. 1. Locate the fill tube and the round foam gasket from the ice maker kit (the gasket may already be installed on the fill tube). If not already done, slide the gasket over the end of the fill tube. Insert the fill tube through the hole in the rear of the refrigerator with the spout facing down, and secure it with two 1/2" hex-head sheet metal screws. Refer to the side diagrams for the following steps. You will be working inside the freezer compartment. 1/2" hex-head sheet-metal screws 1. Slide the plastic fill tube extension (See components table on page 5) over the end of the fill tube as far as it will go (see DETAIL A). NOTE: The plastic fill tube extension is not required for models with open-top fill tube. 2. Flat wiring cover: Install the wiring cover over the fill tube with the wiring harness through the slot. Hook the tab in the side of the wiring cover into the slot in the back cover of the freezer, and secure the cover with the screw you removed earlier (see DETAIL B). Spout Fill tube Foam gasket Installing the fill tube/gasket DETAIL A Fill tube Wiring harness Fill tube extension (See components table on page 5) Installing the fill tube extension DETAIL B Tab Route harness and fill tube through openings Screw Reinstalling the flat cover 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
10
Top/Upright freezer models (continued)
Refer to the side diagrams for the following steps.
1.
Locate the fill tube and the round foam gasket from the ice
maker kit (the gasket may already be installed on the fill
tube). If not already done, slide the gasket over the end of the
fill tube.
Insert the fill tube through the hole in the rear of the
refrigerator with the spout facing down, and secure it with two
1/2" hex-head sheet metal screws.
Refer to the side diagrams for the following steps. You will be
working inside the freezer compartment.
1.
Slide the plastic fill tube extension (See components table on
page 5) over the end of the fill tube as far as it will go (see
DETAIL A).
NOTE:
The plastic fill tube extension is not required for
models with open-top fill tube.
2.
Flat wiring cover:
Install the wiring cover over the fill tube
with the wiring harness through the slot. Hook the tab in the
side of the wiring cover into the slot in the back cover of the
freezer, and secure the cover with the screw you removed
earlier (see DETAIL B).
Installing the fill tube/gasket
1/2" hex-head
sheet-metal
screws
Spout
Fill tube
Foam gasket
Wiring harness
Fill tube extension
(See components
table on page 5)
Fill tube
DETAIL A
Installing the fill tube extension
Reinstalling the flat cover
Tab
Screw
Route harness and
fill tube through
openings
DETAIL B