Amana ART318FFDW Installation Instructions - Page 11

See Detail D.

Get Amana ART318FFDW PDF manuals and user guides View all Amana ART318FFDW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installing the tubing clips Refer to the side diagrams for the following steps. 1. Remove the hex-head screws from the rear access cover, then remove the cover and set it aside. NOTE: If you have a later unit with a metal panel, and a separate, smaller access cover (see DETAIL A), remove the hex-head screw from the access cover. Discard the cover and its screw. Do not remove the hex-head screws from the larger rear access cover. 2. Peel the backing from the adhesive sides of the tubing clips. Press the clips against the back of the cabinet in the right channel at the approximate locations shown in DETAIL B. Center the clips between the fill tube and the top of the access opening. Alternate fill tube design is shown in DETAIL C. 3. For side by side models with a metal access cover, install the water valve bracket to the mounting holes in the cabinet frame using two 1/2" machine screws. See DETAIL D. DETAIL C Alternate fill tube design Fill tube Right channel DETAIL B Tubing Clip Remove hexhead screws from rear access cover DETAIL D 1/2" hex-head machine screws Metal panel Access cover Remove hexhead screw from rear access cover DETAIL A Installing the tubing clips 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
11
Installing the tubing clips
Refer to the side diagrams for the following steps.
1.
Remove the hex-head screws from the rear access cover,
then remove the cover and set it aside.
NOTE:
If you have a later unit with a metal panel, and a
separate, smaller access cover (see DETAIL A), remove the
hex-head screw from the access cover. Discard the cover
and its screw. Do not remove the hex-head screws from the
larger rear access cover.
2.
Peel the backing from the adhesive sides of the tubing clips.
Press the clips against the back of the cabinet in the right
channel at the approximate locations shown in DETAIL B.
Center the clips between the fill tube and the top of the
access opening. Alternate fill tube design is shown in
DETAIL C.
3.
For side by side models with a metal access cover, install
the water valve bracket to the mounting holes in the cabinet
frame using two 1/2" machine screws.
See DETAIL D.
Installing the tubing clips
DETAIL A
Remove
hexhead
screw from rear
access cover
Metal panel
DETAIL D
Remove
hexhead screws
from rear
access cover
Access cover
1/2" hex-head
machine screws
DETAIL C
Alternate
fill tube
design
Tubing Clip
DETAIL B
Right channel
Fill tube