Amana ART318FFDW Installation Instructions - Page 14

Mounting the ice maker

Get Amana ART318FFDW PDF manuals and user guides View all Amana ART318FFDW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Mounting the ice maker Refer to the side diagram for the following steps. 1. Remove and discard the blank connector from the wiring harness. To remove it, lift the locking arm on the side of the blank connector so it is over the tab of the wiring harness connector, and pull the blank connector off. 2. Insert the end of a small-bladed screwdriver under the edges of each of the three ice maker mounting hole plugs in the side of the freezer liner, and pry them out of their holes. You can discard the plugs. 3. For Top/Upright Freezers Only: Partially install two 3/4" hexhead sheet-metal screws into the two top mounting holes (shown in the diagram) of the freezer liner. You will hang the ice maker over these two screws later, so make sure that they protrude out far enough. 4. For Side-By-Side Models Only: Refer to DETAIL A and mount the two mounting clips (from the ice maker kit) to the top mounting holes of the freezer liner with two 3/4" hex-head sheet-metal screws. Make sure that both clips hang straight down and then tighten the screws. SXS MODELS ONLY DETAIL A 3/4" hex-head sheet-metal screws Ice maker clips Hole plugs Tab Lift locking arm over tab Blank connector (remove and discard) Wiring harness connector Installing the ice maker clips 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
14
Mounting the ice maker
Refer to the side diagram for the following steps.
1.
Remove and discard the blank connector from the wiring
harness. To remove it, lift the locking arm on the side of the
blank connector so it is over the tab of the wiring harness
connector, and pull the blank connector off.
2.
Insert the end of a small-bladed screwdriver under the edges
of each of the three ice maker mounting hole plugs in the
side of the freezer liner, and pry them out of their holes. You
can discard the plugs.
3.
For Top/Upright Freezers Only: Partially install two 3/4" hex-
head sheet-metal screws into the two top mounting holes
(shown in the diagram) of the freezer liner. You will hang the
ice maker over these two screws later, so make sure that
they protrude out far enough.
4.
For Side-By-Side Models Only: Refer to DETAIL A and mount
the two mounting clips (from the ice maker kit) to the top
mounting holes of the freezer liner with two 3/4" hex-head
sheet-metal screws. Make sure that both clips hang straight
down and then tighten the screws.
3/4" hex-head
sheet-metal
screws
DETAIL A
SXS MODELS ONLY
Ice maker
clips
Hole
plugs
Tab
Wiring
harness
connector
Blank connector
(remove and
discard)
Lift locking
arm over tab
Installing the ice maker clips