Asus H170-PRO User Guide - Page 66

PCH-IO Configuration, PCI Express Configuration, PCIe Speed [Auto], SATA Controllers [Enabled]

Get Asus H170-PRO PDF manuals and user guides View all Asus H170-PRO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

PEG Port Configuration Allows you to configure the PEG Port settings. PCIEx16_1 Link Speed [Auto] Allows you to configure the PCIEx16 speed for slot 1. Configuration options: [Auto] [Gen1] [Gen2] [Gen3] Memory Configuration Allows you to configure the memory configuration parameters. Memory Remap [Enabled] Set this item to [Enabled] to support DRAM address remapping for 64-bit operating systems. Configuration options: [Enabled] [Disabled] 2.6.4 PCH-IO Configuration This item allows you to configure the PCI Express configuration settings. PCI Express Configuration PCIe Speed [Auto] Allows you to configure the PCIe speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3] 2.6.5 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port. SATA Controller(s) [Enabled] Enables or disables onboard the SATA device. Configuration options: [Disabled] [Enabled] The following items appear only when you set the SATA Controller(s) to [Enabled]. SATA Mode Selection [AHCI] Allows you to set the SATA configuration. [AHCI] Set to [AHCI] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands. [RAID] Set to [RAID Mode] when you want to create a RAID configuration from the SATA hard disk drives. The following items appear only when you set the SATA Mode Selection to [RAID]. CR#1 RST Pcie Storage Remapping [Disabled] This item allows you to enable or disable the RST Pcie Storage Remapping feature. Configuration options: [Auto] [Disabled] [Enabled] 2-32 Chapter 2: Getting started

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
PEG Port Configuration
Allows you to configure the PEG Port settings.
PCIEx16_1 Link Speed [Auto]
Allows you to configure the PCIEx16 speed for slot 1. Configuration options: [Auto]
[Gen1] [Gen2] [Gen3]
Memory Configuration
Allows you to configure the memory configuration parameters.
Memory Remap [Enabled]
Set this item to
[Enabled]
to support DRAM address remapping for 64‑bit operating
systems. Configuration options: [Enabled] [Disabled]
2.6.4
PCH-IO Configuration
This item allows you to configure the PCI Express configuration settings.
PCI Express Configuration
PCIe Speed [Auto]
Allows you to configure the PCIe speed. Configuration options: [Auto] [Gen1] [Gen2] [Gen3]
2.6.5
SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show
Not Present
if no SATA device is installed to the corresponding SATA
port.
SATA Controller(s) [Enabled]
Enables or disables onboard the SATA device. Configuration options: [Disabled] [Enabled]
The following items appear only when you set the SATA Controller(s) to
[Enabled]
.
SATA Mode Selection [AHCI]
Allows you to set the SATA configuration.
[AHCI]
Set to [AHCI] when you want the SATA hard disk drives to use the AHCI
(Advanced Host Controller Interface). The AHCI allows the onboard storage
driver to enable advanced Serial ATA features that increases storage
performance on random workloads by allowing the drive to internally
optimize the order of commands.
[RAID]
Set to [RAID Mode] when you want to create a RAID configuration from the
SATA hard disk drives.
The following items appear only when you set the SATA Mode Selection to
[RAID]
.
CR#1 RST Pcie Storage Remapping [Disabled]
This item allows you to enable or disable the RST Pcie Storage Remapping feature.
Configuration options: [Auto] [Disabled] [Enabled]
2‑32
Chapter 2: Getting started