Asus M2NPV-VM M2NPV-VM User's manual for English edition - Page 36

M2NPV-VM IDE connectors

Get Asus M2NPV-VM PDF manuals and user guides View all Asus M2NPV-VM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

3 . IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s). There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). Single device Two devices Drive jumper setting Cable-Select or Master Cable-Select Master Slave Mode of device(s) Master Slave Master Slave Cable connector Black Black Gray Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. If any device jumper is set as "Cable-Select," make sure all other device jumpers have the same setting. NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. PRI_IDE SEC_IDE M2NPV-VM ® M2NPV-VM IDE connectors PIN 1 1-26 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1-26
1-26
1-26
1-26
1-26
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
Chapter 1: Product introduction
3.
3.
3.
3.
3.
IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE)
IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE)
IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE)
IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE)
IDE connectors (40-1 pin PRI_IDE; 40-1 pin SEC_IDE)
The
onboard IDE connectors are for Ultra DMA 133/100/66 signal
cable(s). There are three
connectors on each Ultra DMA 133/100/66
signal cable: blue, black, and gray. Connect the blue connector to the
motherboard's IDE connector, then select one of the following modes
to configure your device(s).
M2NPV-VM
M2NPV-VM IDE connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
PRI_IDE
PIN 1
SEC_IDE
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE
devices.
If any device jumper is set
as "Cable-Select,"
make sure all other device
jumpers have the same setting.
Black or gray
Drive jumper
Drive jumper
Drive jumper
Drive jumper
Drive jumper
Mode
Mode
Mode
Mode
Mode
Cable
Cable
Cable
Cable
Cable
setting
setting
setting
setting
setting
of device(s)
of device(s)
of device(s)
of device(s)
of device(s)
connector
connector
connector
connector
connector
Single device
Cable-Select or Master
-
Black
Two devices
Cable-Select
Master
Black
Slave
Gray
Master
Master
Slave
Slave