Asus MES-VM MES-VM User Manual - Page 47

I/O Device Configuration

Get Asus MES-VM PDF manuals and user guides View all Asus MES-VM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

4. BIOS SETUP 4.4.2 I/O Device Configuration 4. BIOS SETUP I/O Device Config Onboard FDC Controller [Enabled] When [Enabled], this field allows you to connect your floppy disk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a different controller card to connect the floppy disk drives, set this field to [Disabled]. Configuration options: [Disabled] [Enabled] Onboard Serial Port 1 [3F8H/IRQ4] This allows you to set the address for the onboard serial connector. Serial Port 1 and Serial Port 2 must have different addresses. Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/IRQ10] [Disabled] Onboard Serial Port 2 [2F8H/IRQ3] This allows you to set the address for the onboard serial connector. Serial Port 1 and Serial Port 2 must have different addresses. Configuration options: [3E8H/IRQ4] [2E8H/IRQ10] [Disabled] [3F8H/IRQ4] [2F8H/IRQ3] UART2 Use Infrared [Disabled] When enabled, this field activates the onboard infrared feature and sets the second serial UART to support the infrared module connector on the motherboard. If your system already has a second serial port connected to the onboard COM2 connector, it will no longer work if you enable the infrared feature. By default, this field is set to [Disabled], which leaves the second serial port UART to support the COM2 serial port connector. See IrDACompliant Infrared Module Connector in 3.8 External Connectors. Configuration options: [Disable] [Enabled] ASUS MES-VM User's Manual 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
ASUS MES-VM User’s Manual
47
4.
BIOS SETUP
4.
BIOS SETUP
Onboard FDC Controller [Enabled]
When [Enabled], this field allows you to connect your floppy disk drives to
the onboard floppy disk drive connector instead of a separate controller card.
If you want to use a different controller card to connect the floppy disk drives,
set this field to [Disabled]. Configuration options: [Disabled] [Enabled]
Onboard Serial Port 1 [3F8H/IRQ4]
This allows you to set the address for the onboard serial connector. Serial
Port 1 and Serial Port 2 must have different addresses. Configuration op-
tions: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/IRQ10]
[Disabled]
Onboard Serial Port 2 [2F8H/IRQ3]
This allows you to set the address for the onboard serial connector. Serial
Port 1 and Serial Port 2 must have different addresses. Configuration op-
tions: [3E8H/IRQ4] [2E8H/IRQ10] [Disabled] [3F8H/IRQ4] [2F8H/IRQ3]
UART2 Use Infrared [Disabled]
When enabled, this field activates the onboard infrared feature and sets the
second serial UART to support the infrared module connector on the moth-
erboard. If your system already has a second serial port connected to the
onboard COM2 connector, it will no longer work if you enable the infrared
feature. By default, this field is set to [Disabled], which leaves the second
serial port UART to support the COM2 serial port connector. See
IrDA-
Compliant Infrared Module Connector
in
3.8 External Connectors
.
Con-
figuration options: [Disable] [Enabled]
4.4.2
I/O Device Configuration
I/O Device Config