Asus P I-P6NP5 User Manual - Page 30

P/I-P6NP5 User's Manual, CPU cooling fan connector FAN, WARNING, IrDA-compliant infrared module

Get Asus P I-P6NP5 PDF manuals and user guides View all Asus P I-P6NP5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

III. INSTALLATION 14. CPU cooling fan connector (FAN) This connector supports a CPU cooling fan of 500mAMP (6WATT) or less. Orientate the fan so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the this connector. WARNING: The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. GND +12V III. INSTALLATION (Connectors) FAN +12V GND CPU Fan Power 15. IrDA-compliant infrared module connector (IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure UART 2 Use Infrared in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA. When IrDA is selected in BIOS, COM2 will be disabled. Use the five pins as shown on the Back View and connect a ribbon cable from the module to the motherboard according to the pin definitions. NC GND +5V IRRX IRTX Front View Back View Infrared Module Connector IRTX +5V GND NC IRRX 24 P/I-P6NP5 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
P/I-P6NP5 User's Manual
24
III. INSTALLATION
(Connectors)
III.
INSTALLATION
14.CPU cooling fan connector (FAN)
This connector supports a CPU cooling fan of 500mAMP (6WATT) or
less.
Orientate the fan so that the heat sink fins allow airflow to go
across the onboard heat sink(s) instead of the expansion slots.
Depending on the fan manufacturer, the wiring and plug may be
different.
The red wire should be positive, while the black should be
ground.
Connect the fan's plug to the board taking into consideration
the polarity of the this connector.
WARNING:
The CPU and/or motherboard will overheat if there is
no airflow across the CPU and onboard heatsinks.
Damage may
occur to the motherboard and/or the CPU fan if these pins are
incorrectly used.
GND
CPU Fan Power
+12V
FAN
+12V
GND
15. IrDA-compliant infrared module connector (IR)
This connector supports the optional wireless transmitting and
receiving infrared module.
This module mounts to a small opening on
system cases that support this feature.
You must also configure UART
2 Use Infrared in Chipset Features Setup to select whether UART2 is
directed for use with COM2 or IrDA.
When IrDA is selected in BIOS,
COM2 will be disabled.
Use the five pins as shown on the Back View
and connect a ribbon cable from the module to the motherboard
according to the pin definitions.
+5V
IRTX
IRRX
NC
GND
Back View
Infrared Module Connector
Front View
IRRX
+5V
IRTX
NC
GND